May 12, 2022

Types of Shaft Alignmenttypes of shaft/coupler misalignment  


As I write this, boat yards are checking over systems, and re-familiarizing themselves with the boat they haven’t seen since the fall. Some of these checks can be itemized on a list; others are more intuitive: did the engine make this sound last year? Has the stuffing box drip-rate changed? Where is that darn vibration coming from? Some of these questions can be addressed by checking the alignment of the engine and it’s associated moving parts.

Sometimes big changes happen in the off-season: a new engine, a fresh cutlass bearing, or some fiberglass work on the engine beds has necessitated an alignment. Other times, the natural wear and tear of items under various forces requires an adjustment.

A typical engine-shaft set-up is fairly straightforward, though the way that all the components are aligned may be unfamiliar.

Angles of the Shafta view of the angles of the shaft and engine 

Angles

When a boat is designed and built, the angle of the propeller shaft is set first. The hole the runs through the hull, and the way that the prop strut is set in the hull is carefully measured by the builders (and during any major repair work done thereafter).

Also included in the original plans is the size and strength of the engine beds – based on the size and weight of the engine that will be mounted. The engine is then secured to this strong base using adjustable motor mounts (typically four – one at each corner of the engine). Each corner can then be independently adjusted up and down to provide a change to the height and angle that the engine sits at.

Adjustable Engine Mountdetail of an adjustable engine mount

The term ‘alignment’ is this movement of the engine – raising, lowering and tilting in order to line it up correctly to the angle of the prop shaft. In a new boat, this is a fairly straightforward process. There isn’t a lot of play in the various parts, so there is little room for guessing or error.

In a boat that has had a few (or many) seasons behind it, things get a bit trickier: the engine bed and stringers that support the motor mounts become waterlogged and sag. The adjustable threads and nuts on the motor mounts rust and corrode. The cutlass bearing wears unevenly, creating play. The shaft bends or warps creating new issues.
So – before attempting any alignment, the following should be checked:

• The stringers/bed area that the mounts are secure to are solid. Use percussive testing and a moisture meter to confirm that they are not delaminated, and are strong enough (as designed) to support the weight and vibration of the engine

• That the mounts are in good condition: no cracks, wear, rust or corrosion that might prevent adjustments

• That the mounts are secured to the stringers/bed. This is usually done with lag bolts and an appropriate sealant. Ensure that the lag bolts are tight and secure

• That the propeller shaft is straight and true

• That the prop strut is secured and angled correctly

• That the cutlass bearing isn’t overly worn

• That the stuffing box is in good condition

• That the coupler is in good condition, and that the face of the coupler is true

If any of these items require repair (or are questionable), they should be addressed first. Attempting an alignment before addressing these items can be a losing battle!

Coupler Shaft Stuffing Boxthe coupler, shaft and stuffing box

Alignment steps:

1) Confirm that the shaft angle is correct. This is the base point that the alignment will achieve. If there is any play, movement or change during the alignment, you’ll be back to square one.

2) Slide the propeller shaft inward so that the shaft coupler butts against the engine coupler. With the couplers together, check the initial gap – this is done using a feeler gauge. A maximum of 0.001” of misalignment is acceptable for every inch of coupler face. Therefore, a 3” diameter coupler can have up to a 0.003” gap and still be considered aligned. Any gap larger than this value will require alignment.

3) The alignment is done by manipulating the engine’s motor mounts. If viewing the coupler at it’s face, consider the top, bottom and sides as the numbers on a clock. If the gap is wider at 9 or 3, the engine will need to be adjusted from side-to-side (which can get challenging with bigger engines). A gap at 12 or 6 will requirement adjustment up or down on the motor mounts.

4) Once adjustments are made, continue to re-check the gap. With each check, spin the coupler 180 degrees and cross-check.

5) Once the gap is acceptable, the bolts can be installed and tightened. If possible, this should be done by tightening sequentially, opposite each bolt. Fasteners of appropriate strength should be used, and a torque wrench confirming that the bolts are secure. If in doubt, check with a qualified marine tech on bolt type and strength, washer type and torque spec.

6) Once the work is complete, the motor mounts should be set in their ‘mid-range’ – not at the extreme ends of their travel, as this prevents any future fine-tuning.
Much of this work can be done using minimal tools and experience – but if in doubt at any step, check with a qualified marine technician. Often, some minimal adjustments and maintenance each season can enhance enjoyment and comfort aboard for the rest of the year.

Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.

Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

Related Articles

Wednesday, 09 August 2017 02:52

The moment we all dread. It’s a warm sunny day and you’re out for a cruise. Suddenly the boat shudders beneath you, pings, dings and clangs are heard and you realize that you’ve hit something...

Wednesday, 11 October 2017 05:00

If you walk the aisles at a boat show, visit a marine store, or stop in at a repair shop, you’ll likely be inundated with digital displays, vivid touch-screens, NMEA compatible devices, and...

Wednesday, 08 November 2017 04:38

Water has a funny way of making its way into a boat: through through-hulls, stuffing boxes, leaks, hatches, windows and portholes 

Tuesday, 12 September 2017 06:10

The moment we all dread. It’s a warm sunny day and you’re out for a cruise. Suddenly the boat shudders beneath you, pings, dings and clangs are heard and you realize that you’ve hit something...

Wednesday, 10 May 2017 00:43

Question: Can I buy generic automotive parts or products for my boat, or should they specify ‘marine’?

Tuesday, 11 July 2017 07:16

For most of us – this is the time to make the most of the boating season – launch and set up are done. Systems have been recommissioned. Let the fun begin!

Boat Reviews

  • Prev
The well-known Four Winns brand is now a part of the international boatbuilder Groupe Beneteau and ...
Boats have been in high demand for the past two years and there’s no sign of this easing. ...
When we arranged to interview the designer and manufacturer to write a profile of the X Shore Eelex ...
I am lucky to have the opportunity to helm many types of boats. I am even more lucky to sail boats ...
The weather wasn’t cooperating for our test of the new Fountaine Pajot Isla 40. Rain, storm clouds ...
Last August, we were again invited to the Neptunus Yachts facility in St. Catharines, Ontario to ...
Cruisers Yachts’ 34 GLS is the latest model in the Cruisers Yachts line that includes a dozen ...
On a beautiful summer morning in July, I hopped aboard a new-owner delivery from the Outer Harbour ...
When company founder Marcio Schaefer designed the Schaefer 303, he managed to really dial in the ...
There is an unmistakable look to the Azimut S6 Coupe that will stand out in almost any marina. The ...

Video Gallery

 

 

Viko S35

By Katherine Stone

I am lucky to have the opportunity to helm many types of boats. I am even more lucky to sail boats on champagne fall days when many boats are either being hauled for the winter, or are already under shrink-wrap.

Not only are there great winds – usually offshore, but welcome sunshine and open waters with few boats out enjoying the last days of September. Joining me for the test sail of the Viko S35 was the former publisher of Canadian Yachting, Greg Nicoll, and the Canadian Viko Yachts representative, Eric Beauregard, who had driven down from Montreal.

Read More

 

 

Four Winns H4

 

Four Winns H4By Andy Adams

The well-known Four Winns brand is now a part of the international boatbuilder Groupe Beneteau and the new H4 is a great example of how the design and engineering resources of Beneteau can up the game even for a brand like Four Winns that has a long and distinguished history.

The Cadillac Michigan-built H4 is a brand-new design this year and we think it's especially handsome. The vertical stem bow is all new and innovative. It is a design feature that was chosen to give Four Winns and the H4 a sense of modern and contemporary look while the stern remains more traditional. 

Read More

Destinations

  • Prev
It was the last day of August and we were in Little Current heading south. Our Lasalle winter haul ...
Cowichan Bay is a waterfront village with a row of shops, artisan products, marine supplies and a ...
Instant towns have sprung up in the past, especially on the BC coast. In the late 1850s, Victoria ...
Following the War of 1812, a battle that Canada narrowly won against the United States, the ...
You’ve weathered COVID and you’re ready to book your charter to paradise. You’ve done some ...
If you are looking for an interesting destination for a weekend trip or longer, Quebec City will ...
A holiday often is defined by the experiences we make in unique and beautiful settings. But what ...
St Vincent and the Grenadines is open to tourists and Horizon Yacht Charters are looking forward to ...

West Side Story

by Jennifer M. Smith, drone photos by Alex Nikolajevich

It was the last day of August and we were in Little Current heading south. Our Lasalle winter haul out was still over a month away. The question was: where to now? Friends in Meaford often suggested we sail in for a visit. We never had because we’d always moved north-south on the east side of Georgian Bay. This year we were up for something different. This was the perfect opportunity to cruise the west side of the bay.

We made the 10 a.m. bridge out of Little Current and motor-sailed east southeast in light northerlies. We’d often sailed past Snug Harbour, a nearly land-locked anchorage on the north side of Lansdowne Channel because the chart suggested we’d never make it in there with our six-foot draft. 

Read More

Lifestyle

  • Prev
This week’s Photo of the Week comes from BC. The 99th Grey Creek Regatta was held at the Lakeview ...
Back in 2019 (I believe) your magazine used a pic of Sweet Love, a Ranger Tug 31, in a photo ...
a few shots of my wife Maggie practicing her silks routine on our 1982 C&C in the North Channel ...
Last issue, we took a look at boat names. Little did we know we would get what probably will be the ...
Boat names and puns go together like …. Well, like nothing else. Here’s a couple shared by our pal ...
Frequent Windsor racing contributor to Sailing in Canada Roger Renaud, caught this gorgeous ...
The Kingston Yacht Club (KYC) celebrated its 125th anniversary in the summer of 2021, in all the ...
A study on water levels projects an unprecedented drop of water levels on Lakes Michigan-Huron and ...
Ahoy me hearties. June is Sailpast month, so Keelly and her pal Tracey were themed out as (not ...
You’ve invested thousands and thousands of dollars into your boat so naturally, you want to find ...

Marine Products

  • Prev
What happened. Where did our summer go? Well, never mind that, it’s time to start thinking about ...
Cruising boaters visiting new destinations can face challenges when the marina's shorepower system ...
Worn plastic hatch covers can detract from a boat's appearance and its functionality, especially ...
The first builder of electric boats, founded in 1893, Elco now introduces new designs of its EP-6, ...
More than 3/4 of all recreational boats (power and sail) are under 26 feet and towable.
One of the top requests in the electrification of water transport is for a jet ski that can deliver ...
Many boat toilets have dimensions similar to a five-gallon bucket—and are nearly as uncomfortable. ...
Working alongside a US-based designer and boat building company, Burlington ON-based MarsKeel ...
It’s still vacation time and that means calories don’t count. The Boat Galley Cookbook: 800 ...
Words of exasperation wafting across a marina often signal a boat owner fighting with a jammed ...

News

  • Prev
Parks Canada advises that the Kirkfield Lift Lock will begin single-chamber lockages for through ...
The Four Winns TH36 Catamaran had its world premiere at the Cannes Yachting Festival, September ...
After borrowing boats for a couple of years, longtime J105 fanatic and many-year organizer of the ...
Due to ongoing mechanical issues, the Kirkfield Lift Lock will remain closed for the foreseeable ...
BCI Marine is announcing that it will become Canada's distributor of OXE Marine's ...
US Team Zing’s increased boat speed and improved crew work were no match for the extraordinary crew ...
Vision Marine, founded in Montreal and currently based in Boisbriand QC, in partnership with ...
On Sunday, August 21, the Royal Canadian Yacht Club (RCYC) held its fourth annual ...
While there’s still some good weather left, let’s take a moment to celebrate this summer. Sunny, ...
Light air conditions prevented racing on Saturday, which meant there were three fleet races on ...

RS Electric BoatsSailGP, the international racing series featuring high speed F50 wingsailed catamarans, is partnering with RS Electric Boats – sister brand of sailboat manufacturer RS Sailing – to use the Pulse 63 electric RIB as chase, coach and support boats.

RS Electric Boats will supply SailGP with four Pulse 63s, which were designed to be electric boats from the outset. The unique aerodynamic hull form is designed to support the weight of the batteries while allowing rapid acceleration, functional speeds up to 23 knots and ample range.

 

 

Read More