Feb 25, 2021

Below the Water InspectionWhen the boat is in the water, It’s easy to take for granted the parts of the boat that are under the water. It’s also simple to think ‘everything worked well last year, so I won’t worry about it this year.’

For powerboat owner, while there’s a number of checks to perform on the underwatermachinery before launch, there’s a lot more happening besides propulsion. Powerboats can have stern-drives, trim-tabs, anodes, through-hulls, speedometer pick-ups, and transducers. But beyond this, the transom, chines and overall condition of the hull and coatings should be inspected. Here’s a quick checklist:

• Sterndrive – check to ensure that the drive shifts into gear, and spins freely when the engine is in neutral (by shifting in and out of gear at the helm, while the engine is OFF). Check to make sure that the gear oil is clear and at the appropriate level. Check the condition of the drive bellows – if they are split or cracked, they should be replaced.

Below the Water Inspection• Check the condition of the anodes – the stern-drive unit will have multiple anodes, as will the prop shaft and trim tabs. Some power vessels will have large anodes mounted to the transom below the waterline. While looking at the anodes, check to see if there is any corrosion on any underwater metal components, or if paint on the drive needs to be touched-up.


• Check the prop for any chips or damage. Check that the prop retaining nut is tight, and any cotter pins are secure

• Check the trim tabs for damage, and ensure that they are functioning through their full range of motion. Check fluid levels and top-up as necessary.

• Check the speedometer pick-up and hose for any damage – replace any damaged components

• Check transducers and through-hulls for damage, and to ensure that they are securely mounted

• Check the condition of the hull and transom. Use a small hammer or tool to tap on the hull to see fi there are any ‘soft’ spots, which may indicate water intrusion. Check chine edges, and any trailering damage. Check bow hooks, and cleats for wear or separation.

• Check the condition of the coatings – whether bare gelcoat, or antifoul. For bare hulls, clean using an appropriate hull cleaner. For hulls with antifouling; Sand, clean, touch-up and coat where necessary

Below the Water InspectionSailboats differ. Through-hulls and transducers may be similar, but underwater machinery is kept to a minimum. The major difference is the keel, which can necessitate some added considerations.

For most production sailboats, the cast iron or lead keel attaches to a keel stump (made of fibreglass) via threaded rods entering the boat’s bilge and secured with a threaded nut. Because the keel is fashioned of two joined parts, the keel flexes and moves, developing the ‘keel smile’ at the joint.

As water enters the joint, and subsequently freezes over the winter, the joint will widen naturally. This is an important area to check each year, both for optimum sailing performance and vessel longevity.

There are a few steps that can be taken to minimize damage and to repair this joint prior to launch:

• Ensure that the keel bolts/nuts are tight. Because the keel is ‘hanging’ in the cradle, drawing downward pressure, make sure that the cradle pads are slightly loose against the hull, therefore closing the gap between the cast iron or lead keel, and it’s fibreglass mating surface

• Once the gap is closed as tight as it can, tighten the keel nuts inside the boat’s bilge. This may require some oversized sockets and lubricants to both loosen and tighten the threaded fittings.

• Sealants and/or fillers can be used to fill any/all voids, and to finish or fair the exterior joint

Coatings and antifouling products can differ widely from powerboats – the entire hull below the water should be inspected, prepped and coated as necessary, following the manufacturers applications directions.

One of the few advantages of living in a climate that requires boats to be pulled from the water each year, is that ability to inspect and maintain the vessel’s hull. As always, consult an expert if you have questions, or if there are maintenance tasks that are beyond your scope or comfort level.


Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.

Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

Related Articles

Wednesday, 09 August 2017 02:52

The moment we all dread. It’s a warm sunny day and you’re out for a cruise. Suddenly the boat shudders beneath you, pings, dings and clangs are heard and you realize that you’ve hit something...

Monday, 28 January 2013 09:46

When it comes to making environmentally friendly choices, the tradeoff is not always paying more for something that doesn't work as well. Boat owners seeking a "greener" sacrificial anode have an...

Wednesday, 10 May 2017 00:43

Question: Can I buy generic automotive parts or products for my boat, or should they specify ‘marine’?

Monday, 24 March 2014 15:51

Understanding how systems really work – and degrade over the winter – can help you prepare your boat for a trouble-free season. Here’s a guide from a pro…Sometimes the most daunting thing about...

Tuesday, 11 July 2017 07:16

For most of us – this is the time to make the most of the boating season – launch and set up are done. Systems have been recommissioned. Let the fun begin!

Saturday, 09 July 2016 21:10

One of the largest, if not the largest,boatyard in Nova Scotia is South Shore Marine. Located around the corner from village of Chester, the yard, which began in the late 70s, now hauls about 500...

Boat Reviews

  • Prev
In the February 2020 issue of Canadian Yachting magazine, we featured our review of the Neptunus ...
A luxury sport cruiser like the all new Prestige 420S has it all—lines that are easy on the eyes, a ...
Once again, Cruisers Yachts is leading the market for day boats with their new 42 GLS model that ...
Optimized sailing performance and comfortable living – a sweet ride. The expression that came to ...
This is such an exciting time in boating! While we feel very sorry for people whose health and ...
For many, the 2020 sailing year will be one to go down into the books as “different”. With delayed ...
What perfect timing! Beneteau is has just announced their new Antares 11 model for North America ...
Commodore’s Boats is a full-service shipyard with over 50 years of generational history and ...
The Oceanis Yacht 54, younger sister of the Oceanis 62, embodies the innovation that has always ...
Beneteau announces the launch of the latest addition to the Antares range! With a length overall of ...

CY Virtual Video Boat Tours

Virtual Boat ToursWe all love boats and nothing can break us up! So, what better way to spend our time than looking at interesting boats and going aboard in a virtual ride or tour. We have asked our friends at various dealers and manufacturers to help us assemble a one-stop online resource to experience some of the most interesting boats on the market today. Where the CY Team has done a review, we connect you to that expert viewpoint. If you can’t go boating, you can almost experience the thrill via your screen. Not quite the same, but we hope you enjoy our fine tour collection.

 

Read more about the CY Virtual Boat Tours....................

 

 

 

Neptunus 750 Enclosed FlybridgeBy Andy Adams

In the February 2020 issue of Canadian Yachting magazine, we featured our review of the Neptunus 750 Flybridge, the company’s flagship yacht. The boat had been bought by a gentleman from Newfoundland and we reviewed it just before it was to be delivered.

We learned later that the boat did not leave immediately after delivery. The story is that the new owner reconsidered the beautiful big open flying bridge layout. 

Read More

Destinations

  • Prev
On Friday, April 2 at 7 pm ET on TVO and streaming anytime after that on tvo.org and the TVO ...
Salt Spring Island, the largest among the Gulf Islands, has a certain mystique—much of it having to ...
Located in Lake Huron, the internationally significant Manitoulin Island is the largest freshwater ...
In Part I, Sheryl Shard ended the story at June and the start of Hurricane Season when they were ...
You likely aren’t quite ready to travel yet, but we have our fingers crossed that we can all fly ...
Ontario’s best-kept secret, the Trent-Severn Waterway National Historic site holds the key to ...
Located on the sunny south shore of the harbour, the Marina is on pilings over the water, offering ...
The approach to the Chemainus Municipal Dock from Stuart Channel is straightforward and is ...
I leaned my head back into the water and floated easily. Having spent my childhood playing in ...
History: right after gym and just before chemistry class. Fifty minutes of naming the prime ...

View of Ganges HarbourText and Photos by Marianne Scott

Salt Spring Island, the largest among the Gulf Islands, has a certain mystique—much of it having to do with locally produced food. It started thousands of years ago when the Coast Salish First Nations used the Island as a summer camp, collecting wild foods while also processing the abundant sea food for winter sustenance.

In the 19th century, five main groups settled here and began farming: Northern Europeans—some of whom had abandoned gold rush dreams; Hawaiians brought here by Vancouver Island’s second governor, James Douglas...

Read More

Lifestyle

  • Prev
As a life-long marine journalist, it has often occurred to me, that it’s a big ...
Here’s a dramatic photo of the Week from Jansin Ozkur. “Walking along the lake Ontario, noticed the ...
At the end of summer 2020, amid all the restrictions, we were able to shoot our film, Generations ...
Last issue, Mike Wheatstone, our Boat Nerd started a conversation about solar power. While many of ...
Oak Bay Marina achieves eco-certification in Clean Marine BC, which helps boating facilities to ...
OK, stop the presses. This photo just came in from Beacon Bay. Clearly those folks know how to get ...
Back in the day, the publisher of a magazine would receive a bound copy of the year’s monthly ...
Boaters on BC’s West Coast have heard the story of the garbage pickers of the Marine debris removal ...
Skipper John “Drew” Plominski is hoping that lightning doesn’t strike twice. Plominski, whose boat ...
The Association provides a forum for exchanging information, tips and access an advocate on behalf ...

A Freedom Boat Club StafferAs a life-long marine journalist, it has often occurred to me, that it’s a big leap to lay out the cash, (especially for those with no previous boating experience), to try it out. How does someone even know that they will like boating it if they haven’t tried it? 

Well, joining a boat club, or a yacht club that has boats available for members to use, can get you started without the big financial commitment and with the support of the club’s education and resources. Try before you buy.


Read More

National Invasive Species Awareness WeekThis week, Feb. 22-26, is National Invasive Species Awareness Week and the American Boat and Yacht Council (ABYC) released an animated video to raise awareness about the threat Aquatic Invasive Species (AIS) pose to the boating industry and what manufacturers can do to limit the spread.

AIS can damage ecosystems and negatively impact fishing and the future of the boating lifestyle. Boat access to many aquatic resources has been limited due to AIS concerns and AIS infestation can result in serious damage to boats and their components. Invasive plant life can foul propellers,

Read More

Marine Products

  • Prev
The YETI Tundra 65 is their most versatile cooler, just as adept at keeping your catch cold as it ...
A good night’s sleep on the boat is a great pleasure indeed and custom bedding from SeaSwag ...
When bright white light is needed on board, a compact Sea Hawk-350 LED Light Bar from Hella marine ...
First time in many years I was lucky enough to test both the GMC Canyon and the Chevrolet Colorado ...
Unlike cars and homes, boats can be difficult spaces in which to create a quality listening ...
Yamaha Motor Canada has launched an upgraded 4.2-litre V MAX SHO® outboard, offering a full 40 ...
Holidays are perfect times for daydreaming and anyone who loves boating, will love ...
Bringing back a boat's showroom shine is fast and easy with the award-winning World's Best Dual ...
The JBL Click Bluetooth® wireless controller from Prospec Electronics adds fingertip control of ...

News

  • Prev
According to the Nova Scotia Tourism website, Theodore Tugboat began his travels in 1989, created ...
On Monday, March 29th, fire broke out in a group of power boats stored on the hard and still under ...
On April 1st, 2021, Wright’s Marina joined two other small, independent facilities: Hindson Marina ...
Our new feature is CYOB’s look at boats and food – two words that are almost synonyms! That’s a lot ...
This Maritime Radio ONLINE SELF-STUDY program is a completely integrated version of Canadian Power ...
Finding the right PFD can seem like a daunting task and extends beyond finding one that fits and ...
I start off my column by saying Wow!!  What a market! I have never seen such panic buying in ...
Yanmar Holdings has entered into a collaboration with design house “fragment design”, headed by ...
From January 25 - March 31, Parks Canada is asking the public to read its Draft Management ...
As the most innovative family-run boatyard in Europe, time and again Frauscher's premium ...

invasive species video 400AIS can damage ecosystems and negatively impact fishing and the future of the boating lifestyle. Boat access to many aquatic resources has been limited due to AIS concerns and AIS infestation can result in serious damage to boats and their components. Invasive plant life can foul propellers, jam impellors and cause bilge pump failure. Mussels can attach to boats and negatively affect performance, attach to engines causing component failure, and obstruct water lines causing system failure.

Read more....

 

 

fibreglass recycling part2 400 By Jay Weaver

Interest in finding alternative uses for used fiberglass can spark creativity and innovation. For example, a partnership involving the US, Ireland, and Northern Ireland Universities called Re-wind developed some interesting civil engineering project ideas for reusing and repurposing fiberglass blades. These include using decommissioned blades in civil engineering projects as part of powerline structures or towers, or roofs for emergency or affordable housing. In Northern Ireland, Re-wind is also considering piloting them for use in pedestrian bridges along greenways.

Read More about Fiberglass recycling....

 

 

Theodore TugboatAccording to the Nova Scotia Tourism website, Theodore Tugboat began his travels in 1989, created by Cochran Entertainment, with master model maker Fred Allen, as a children's television series inspired by the Halifax Waterfront and the stories Andrew Cochran would tell his son at bedtime. The CBC television program Theodore Tugboat ran from 1993 to 2001.

A working replica of Theodore, named "Theodore Too" was built in Dayspring, Nova Scotia. Designed by Fred Allen and Marius Lengkeek, the tug was launched on April 19, 2000 at the Snyder Shipyard. After a successful tour of several North America ports, it made its home in Halifax. 

Read More