June 27, 2019

Placement Of BellowsA diagram showing the placement of bellows between the engine (inside the boat) and the stern drive (outside of the boat)

In any boat with an inboard engine, the machinery that the drives the boat moves through the hull. An engine drives a propeller shaft, at the end of which is the propeller that moves the vessel through the water. This is as true of a bow-rider or a large sailboat, only the arrangement is different.

In a boat with a traditional prop and shaft arrangement, the engine’s transmission turns a straight shaft, at the end of which is a propeller. The shaft passes from inside of the boat, where it is connected to the engine/transmission, through the boat’s hull to the open water around the boat. The shaft has to be free to turn, but the hull also needs to be watertight. The way to meet both needs is to include a stuffing box at the point that the shaft moves through the hull.

The name is a bit deceiving – it is not box-like, and it isn’t filled with stuffing – rather, it is a tube that surrounds the shaft, with a tightening nut on one end. Behind and inside this nut, is a waxed rope that surround the shaft, but allows it to turn freely. The waxed rope (or ‘stuffing) keeps water out, while allowing the shaft to spin. Over time, with seasonal storage and friction through use, the stuffing wears down and loosens. This allows water to enter the bilge more readily, and is often the first sign that the stuffing box should be re-packed.

There are many types of stuffing boxes, with new ‘dripless’ technology readily available. In a more traditional stuffing box, dripping water (about one drip per minute) is the norm. The packing can be changed in or out of the water, with out without the prop-shaft installed – that said, it’s my experience that (due to the angles involved) its often much easier to do with the boat out of the water, with the prop and shaft removed first. However, in a pinch, and onboard, in water repair is often possible (and more cost effective).

Pro and ShaftPacking can be purchased at many marine chandleries, in a variety of thicknesses (so its important to note what thickness is required for your set-up before you purchase). A pick (or specialty packing removal tool) will come in handy to remove old packing, as well as oversized adjustable wrenches to hold the stuffing box nut, and lock nut. Loosen the lock nut, remove the nut (or slide it back on the shaft), and inside the box itself will be the old stuffing. Pick or pry out the old packing material and cut the new packing to fit. To fit new packing, I wrap the cord around the shaft three and a half turns, and then make a cut using a sharp knife, along the shaft. This gives me three strands of packing that are exactly the circumference of the shaft. Pack each strand into the stuffing box, making sure that the seams oppose each other (don’t line up the seams on the same side or angle). Once re-packed, the nut and lock nut can be replaced. Tighten the nut to the point where the stuffing box drips once per minute, but not so tight that the shaft can’t turn freely.

Stern drives

On boats with sterndrives, the machinery that runs through the hull are protected by ridged rubber boots or sleeves called ‘bellows’. Most stern-drives have three bellows: One for the shaft (connecting the engine inside the boat to the stern-drive outside of the transom) called the ‘U-Joint Bellows’, another for the cable that controls shifting (called the ‘shift cable bellows’), and a third for the exhaust. Because stern drives move side-to-side for turning, and up/down for trim, the bellows are continuously in motion, and are susceptible to ripping, tearing and wear. It’s common practice to need to replace bellows over time. A tear in the bellows can allow water to enter the boat quite quickly – so it’s an important maintenance item to check over regularly.

If you’re mechanically inclined, there’s money to be saved in a DIY bellows job, but there are a number of tools and tricks that make this an ambitious job for many boat owners.

In either case – a stuffing box or bellows arrangement, water entering the boat at too fast a rate can (at worst case) cause damage or sinking – at best case it’s an annoyance! Make a review of these systems a regular item on your checklist, and have them repaired as soon as you notice wear or damage.
Safe boating!

Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.

Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

Related Articles

Monday, 28 January 2013 09:46

When it comes to making environmentally friendly choices, the tradeoff is not always paying more for something that doesn't work as well. Boat owners seeking a "greener" sacrificial anode have an...

Wednesday, 10 May 2017 00:43

Question: Can I buy generic automotive parts or products for my boat, or should they specify ‘marine’?

Monday, 24 March 2014 15:51

Understanding how systems really work – and degrade over the winter – can help you prepare your boat for a trouble-free season. Here’s a guide from a pro…Sometimes the most daunting thing about...

Tuesday, 11 July 2017 07:16

For most of us – this is the time to make the most of the boating season – launch and set up are done. Systems have been recommissioned. Let the fun begin!

Tuesday, 09 August 2016 14:28

We couldn't have asked for a better day to test the Fairline 32 at Niagara-on-the-Lake, Ont. The Niagara river just above Lake Ontario...      

Saturday, 09 July 2016 21:10

One of the largest, if not the largest,boatyard in Nova Scotia is South Shore Marine. Located around the corner from village of Chester, the yard, which began in the late 70s, now hauls about 500...

Boat Reviews

  • Prev
When we arranged to interview the designer and manufacturer to write a profile of the X Shore Eelex ...
Last August, we were again invited to the Neptunus Yachts facility in St. Catharines, Ontario to ...
Cruisers Yachts’ 34 GLS is the latest model in the Cruisers Yachts line that includes a dozen ...
On a beautiful summer morning in July, I hopped aboard a new-owner delivery from the Outer Harbour ...
When company founder Marcio Schaefer designed the Schaefer 303, he managed to really dial in the ...
There is an unmistakable look to the Azimut S6 Coupe that will stand out in almost any marina. The ...
No longer an outlier or a flash-in-the-pan idea, electric boating is fast becoming a viable ...
Sea-Doo’s all-new Switch marries the performance of a personal watercraft with the versatility of a ...

Video Gallery

 

 

X Shore Eelex 8000By Andy Adams

100% Electric performance available now

When we arranged to interview the designer and manufacturer to write a profile of the X Shore Eelex 8000 for the June 2021 issue of Canadian Yachting magazine, it was on the understanding that we always prefer to actually drive and experience the boats we write about, and we were especially keen to drive the X Shore when BCI Marine here in Canada, got their first boat from Sweden.

There has been a lot of media attention around everything electric lately, especially electric vehicles, but so far, most electric boats are a concept, not yet a reality. The X Shore Eelex 8000 is a reality and a very impressive one at that.

Read More

 

 

 

Neptunus 650EBy Andy Adams

Last August, we were again invited to the Neptunus Yachts facility in St. Catharines, Ontario to run and review their latest yacht, a 202650E at their marina by Lake Ontario. Keen readers of Canadian Yachting might recall reading about a Neptunus 650 back in 2016 and while this is the same proven hull, Neptunus is a custom builder and the 2022 650E here has a totally new interior design and layout.

Neptunus builds bespoke yachts. The reality is that no two Neptunus Yachts are the same. Each is individually tailored to its owners tastes and activities and is finished to their specifications. 

Read More

Destinations

  • Prev
Instant towns have sprung up in the past, especially on the BC coast. In the late 1850s, Victoria ...
Following the War of 1812, a battle that Canada narrowly won against the United States, the ...
You’ve weathered COVID and you’re ready to book your charter to paradise. You’ve done some ...
If you are looking for an interesting destination for a weekend trip or longer, Quebec City will ...
A holiday often is defined by the experiences we make in unique and beautiful settings. But what ...
St Vincent and the Grenadines is open to tourists and Horizon Yacht Charters are looking forward to ...

Marianne ScottBy Marianne Scott

Instant towns have sprung up in the past, especially on the BC coast. In the late 1850s, Victoria grew overnight into a tent city when hordes of prospectors stopped by to provision for their quest to get rich in the Fraser goldfields. The tents were followed quickly by brick hotels, stores and brothels. Prince Rupert began as a tent town after it was chosen as the Grand Trunk Pacific Railway’s terminus, then built more permanent structures.

But no place went up overnight like Ladysmith, where coal baron James Dunsmuir moved his miners “stock, lock and barrel” after coal seams further north on Vancouver Island had been exhausted.

Read More

Lifestyle

  • Prev
Ahoy me hearties. June is Sailpast month, so Keelly and her pal Tracey were themed out as (not ...
Things are busy on the Trent already and it’s barely June. Mike Gridley sent us this shot last ...
From cottage boats to luxury cruisers, there have been a host of major design changes over the past ...
Thanks to Louise from Gyles Sails and Marine for catching us up on this weekend’s massive parts ...
The marine industry provides exciting opportunities for Canadians. Every month CYOB will introduce ...
There are two POTWs this time. The reason? Guilt. We are picking up the first one from the internet ...
So, I’m at Mobility Cup in Nepean, across the river from Ottawa. I’ve participated in Mobility Cup ...
Emirates Team New Zealand, who introduced foiling to America’s Cup competition in 2012, is ...
Our own Ask Andrew ‘floated his Fanny down the Ganny’ in the annual boat race held on Ganaraska ...
While there’s all kinds of discussion, particularly in NZ, about the plan to defend the 37th ...

Marine Products

  • Prev
The little darlings can’t wait to get on the boat. Just make sure they have properly fitting PFDs ...
With a bold, fresh look and key features, the new JBL-R4500 is the latest in the WAKE Series of ...
When the twist-type connector was invented in 1938, production boats were made of wood and didn't ...
Luxor Marine & RV products offer boat owners an innovative architecturally pleasing range of ...
The club's first digital guide is the collaborative effort of dozens of CCA members and now ...
The days are lovely and what better way to celebrate than heading to the engine compartment. Here ...
While collapsible bimini tops offer boaters a welcome escape from direct sun, deployment and ...
Volvo Penta is launching its Assisted Docking system as a retrofit upgrade for many yacht owners ...
Don’t let offshore emergencies turn into disasters. SeaKits help to prepare you for emergencies at ...
It’s one of the best things about sailors: we hate to give up on our equipment. But if you’re like ...

News

  • Prev
Hello Lake Ontario Boaters. As you know, the much anticipated PORTS Lake Ontario Guide is in ...
Watching whales and other marine mammals in their natural surroundings is exciting. It gives us an ...
Tom Brady couldn’t have thrown a better spiral. This is a shot of my handsome son, Will, carrying ...
A strong contingent of 28 Canadian sailors, including Tokyo 2020 Olympians Ali ten Hove, Mariah ...
Wellcraft teamed up with American naval architect, Michael Peters, and talented yacht designers, ...
Following success in the Nordics and New Zealand, Skipperi is coming to Toronto with 15 new, fully ...
Candela, the Swedish company that is revolutionizing electric boating with its hydrofoiling ...
Scrub Island Resort, Spa & Marina has announced plans for the addition of a new petrol station ...
SailGP, the international racing series featuring high speed F50 wingsailed catamarans, is ...
First, they were closed - as of May 2, many of the Canada Border Services Small Vessel Reporting ...

RS Electric BoatsSailGP, the international racing series featuring high speed F50 wingsailed catamarans, is partnering with RS Electric Boats – sister brand of sailboat manufacturer RS Sailing – to use the Pulse 63 electric RIB as chase, coach and support boats.

RS Electric Boats will supply SailGP with four Pulse 63s, which were designed to be electric boats from the outset. The unique aerodynamic hull form is designed to support the weight of the batteries while allowing rapid acceleration, functional speeds up to 23 knots and ample range.

 

 

Read More