Feb 14, 2019

Ground Bus BarGrounding is always an interesting idea when on a boat. Can a boat be ‘grounded’ when it’s in the water?


Electrical ground is a term used to describe the reference point in an electrical circuit from which voltage is measured, a common return path for electric current, or a direct physical connection to the earth.

Connection to ground is also important in order to trigger protective mechanisms in the event of failure of internal insulation, and also limits the build-up of static electricity.


‘Ground’ is misleading – in that the term in also used in cell phones, cars and boats – none of which are connected to the earth. A different but suitable term is ‘common’. A ‘common’ connection is usually a large conductor (wire) attached to one side of the power supply. The black (negative) conductor running from the boat’s battery to the engine block, could be called ‘common’ rather than ‘ground’.

So why is a ‘ground’ important on a boat?
Wiring Diagram A simple wiring diagram showing the battery, engine block ground, and ground bus-bar


If an electronic device develops a short-circuit from the power supply side to the equipment’s metal case, the case would then be ‘hot’ and would be a potentially dangerous source of electrical shock or ignition. By ‘grounding’ each appliance (whether AC or DC), you are providing an immediate and easy path for the electricity to travel, eliminating the danger of shock and ignition (and reducing the possibility of corrosion). On a boat, this path to ‘ground’ is generally to the engine block. A typical set-up on a boat includes a heavy gauge cable running from each negative battery post to the engine block grounding post. Each electrical appliance is also grounded to a main bus bar, and the bus bar is grounded, using a cable running to the engine block grounding post, as well.

A few important notes about this set-up:

1) Each cable used should be checked against an ampacity chart (discussed in part 1 of this series) to ensure that the cable size is correct, given the amount of current being carried, and the length of cable run

2) Each cable should be secure and torqued to specifications, using appropriate connections (discussed in part 2 of this series)

3) Grounds should be checked periodically, using a multimeter. This will ensure that short circuits, corrosion, and loose connections haven’t crept in, reducing the effectiveness of the grounding efforts.



Bonding WireNote the forward keel boat, with a bonding wire running between it and a common bonding bus bar

‘Bonding’ is a similar but distinct term. Bonding is the practice of electrically tying together all the large metal objects on a boat. This serves multiple purposes: prevents corrosion damage, provides lightening protection, and serves to reduce static electricity build up and provides ignition protection. The items commonly tied together include: fuel tanks, metal casings (water heaters, as an example), keel bolts, propellers/shafts, engine, transmission, stern-drive, and mast steps. The key to a good bonding system is the use of short-runs, with high-conductivity wiring: tinned-copper wiring, of at least #8 AWG (6 AWG if lighting protection is desired) is the rule of thumb suggested. Many bonding systems employ multiple bus bars or a common grounding conductor in order to keep these wire runs as short as possible. The bonding cables used to connect electrical equipment (AC and DC panels, as an example) should be larger than the current-carrying wiring in the circuits (so that if there is a short to the equipment casing, the bonding cable may carry current – and the cabling should be large enough that it wont melt and start a fire).

A typical set-up involves each component to be bonded, bonded separately. This means that components aren’t wired together in series; rather, each component should be bonded individually to a common ground bus, and that ground bus ground to the battery negative post.

Fuel Tank Bonding Wire A fuel tank showing a bonding wire (8AWG) running between the fuel tank and a common bonding bus bar>

A good bonding system will have multiple sized conductors to account for each application. Each component will be bonded individually, and any bonding conductors should be rated to carry current, even though carrying current is not the purpose of bonding.

It’s particularly important to review both grounding and bonding on a boat that has had any equipment changes, electrical upgrades or installations, or significant changes to wiring. Older boats often have incomplete or partial grounding/bonding, and therefore don’t function to protect the boat. Winter layup is a great time to review your systems to make sure that they are installed correctly and are functioning as designed.

 

 


Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.


Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Related Articles

Wednesday, 09 August 2017 02:52

The moment we all dread. It’s a warm sunny day and you’re out for a cruise. Suddenly the boat shudders beneath you, pings, dings and clangs are heard and you realize that you’ve hit something...

Wednesday, 11 October 2017 05:00

If you walk the aisles at a boat show, visit a marine store, or stop in at a repair shop, you’ll likely be inundated with digital displays, vivid touch-screens, NMEA compatible devices, and...

Wednesday, 08 November 2017 04:38

Water has a funny way of making its way into a boat: through through-hulls, stuffing boxes, leaks, hatches, windows and portholes 

Tuesday, 12 September 2017 06:10

The moment we all dread. It’s a warm sunny day and you’re out for a cruise. Suddenly the boat shudders beneath you, pings, dings and clangs are heard and you realize that you’ve hit something...

Wednesday, 10 May 2017 00:43

Question: Can I buy generic automotive parts or products for my boat, or should they specify ‘marine’?

Tuesday, 11 July 2017 07:16

For most of us – this is the time to make the most of the boating season – launch and set up are done. Systems have been recommissioned. Let the fun begin!

Boat Reviews

Video Gallery

 

 

Beneteau Oceanis Yacht 54By Zuzana Prochazka

Beneteau saw an opportunity to add a little thrill to any cruising adventure, so they took the hull of the First 53 racer (introduced just last year), and with a few fashionable changes, created the Oceanis Yacht 54, the new entry-level of Beneteau’s swanky Oceanis Yacht line. The result is a performance cruiser that sails like a witch and looks like a grande dame.

Design

Roberto Biscontini is the naval architect and Lorenzo Argento created the details of the exterior and interior design. 

Read More

Destinations

  • Prev
Over the course of four days in September 1864, representatives from Prince Edward Island, Nova ...
The new owners of L’Orignal Marina offer boaters a new destination. Located in a charming ...
On Friday, April 2 at 7 pm ET on TVO and streaming anytime after that on tvo.org and the TVO ...
Salt Spring Island, the largest among the Gulf Islands, has a certain mystique—much of it having to ...
Located in Lake Huron, the internationally significant Manitoulin Island is the largest freshwater ...
In Part I, Sheryl Shard ended the story at June and the start of Hurricane Season when they were ...
You likely aren’t quite ready to travel yet, but we have our fingers crossed that we can all fly ...

Riverest MarinaThe new owners of L’Orignal Marina offer boaters a new destination. Located in a charming francophone village in Eastern Ontario, this joined marina and restaurant venue is the ambitious initiative of long-time entrepreneur André Chabot and biologist Alexandra Quester, both residents of L’Orignal.

The purchase of the L’Orignal Marina was made official in November 2020. The new year was barely underway when all 50 available slips were already reserved. No wonder the addition of member and visitor slips is already planned for the 2022 season – the 2021 count is up to 62 power and sail already. At the moment, the Riverest Marina offers boaters a stop where they can launch their boat...

Read More

Lifestyle

  • Prev
Last issue we featured a story about the engagement proposal aboard Via-Mara, a 1969 Trojan 42 Aft ...
With thanks to Sail Canada, here’s a collection of photos that are Olympic quality. Clearly our ...
Wow. That was a lot of fun reading the collection of boat names that came in from all over the ...
No individual had a greater impact on the modern sport of sailing than Bruce Kirby. Known and ...
Just off The Ocean Race European Tour, Daniel is setting his sights on competing in The Ocean Race ...
After being our fearless leader and publisher since CYOB kicked off, Greg Nicoll, handed over the ...
Swim Drink Fish is spearheading the Vancouver Plastic Cleanup by installing, maintaining, and ...
With but four weeks to go, Sarah is in Japan, staying safe while acclimatizing to the heat at ...
MJM is a different kind of boat builder, second generation family owned and operated, we design and ...
Stuart Hendrie, a pro photographer sent along this photo of the pirate ship in Jordan Ontario. Many ...

Marine Products

  • Prev
Watermakers take ocean water and create perfect drinking water using reverse osmosis. A Schenker ...
If you’re headed out for a weekend afloat or on a week-long cruise you often must park your vehicle ...
Ten years ago, St. Margaret’s Bay (Halifax), Nova Scotia-based SailTimer Inc. made the first ...
Between the odor and working in confined spaces, replacing an onboard sanitation line is never a ...
For many boat owners who have gear to tote and the occasional stretch of bumpy road to negotiate, a ...
The 2022 Sea-Doo Switch is a re-imagined pontoon that makes hitting the water more accessible than ...
On the water audiophile-quality sound is attainable with the new JBL-R3500 source unit. The latest ...
An environmentally friendly product for refinishing your teak, hemp wood finishing oil is an ...
August means cruising, entertaining and enjoying summer at its finest. And that means food and ...
A Bluetooth-enabled phone or tablet is ideal for streaming music, but it's often stowed safely away ...

News

  • Prev
Royal Canadian Yacht Club’s Defiant completed a six-race sweep of the Cup for Canada over Zing, the ...
On September 6, Groupe Beneteau laid out its course to develop new boating experiences, new ...
Last Friday, the first ever Canada’s Celebration of Sailing honoured the season for Sailing in ...
Boating Ontario is very proud to have Transport Canada’s Office of Boating Safety jump on ...
Montreal-based Vision Marine Technologies, Inc. is headed to the Lake of the Ozarks Shootout to ...
Summer is in full swing with Canadians enjoying time outside and on the water. So, while enjoying ...
On July 23 last year, CYOB published a piece on a beautifully restored 1967 Trojan 42 Motor ...
HanseYachts AG presents RYCK, its third motorboat brand carrying the "Made in Germany" label. The ...
“We are all proud of our athletes and coaches who have dedicated themselves to push Canadian ...
Collingwood, ON hq’d Limestone Boat Company – owner and builder of Aquasport Boats, Limestone Boats ...

Mia and Caleb's EngagementOn July 23 last year, CYOB published a piece on a beautifully restored 1967 Trojan 42 Motor Yacht in Oromocto NB. (That piece was also expanded in CY magazine later in the year.)

One of our Canadian Yachting contributors, Denise Miller, had shared the article on my social media and a young man reached out and asked if she could connect him with the owners of the boat, Dave and Barb. Denise leapt into action and Dave and Barb were thrilled. They concocted a plan that the young lady, Mia, thought she was coming to model for a sales brochure for Dave to do charter tours.

Read More