Carver Marquis Plant Tour – July 2016

Carver Marquis front entrance

By Andy Adams

Last July, I had the pleasure of traveling to Wisconsin on behalf of Boating Industry Canada. I had been invited to take a plant tour of the Carver Marquis yacht building facilities. The company has introduced some important new manufacturing techniques and technologies that we were keen to see firsthand.

This was not my first trip to the Carver Marquis plant, but when I was last there, they were building models that have since been replaced with all new designs that are built using vacuum infusion process.

Many boat builders use open molding where the layers of fiberglass are put in one at a time and allowed to set up before the next layer is applied and rolled out. It’s a time-honored way of boat building but that doesn’t make it the best choice. Vacuum infusion involves applying the gelcoat to the mould, letting that set up and then laying in all of the fiberglass cloth and mat, and the reinforcing parts and cores, dry. Then an air tight plastic membrane is laid over, sealed around the edges with special sealing compound, and with the vacuum lines and resin feed lines attached, the dry fiberglass products are all resin infused at one time.

The advantages are significant although the complexity is much higher. In the hands of skilled and knowledgeable technicians, the finished product can potentially be both stronger and lighter by more precisely controlling the amount of resin to glass and also because the materials are all infused at one time, so there are no bonding issues between one layer and the next.

For the boat builders in the shop, the plastic membrane that allows them to create the vacuum between the membrane and the mold, also keeps many of the volatile organic compounds [VOCs] captured within the material itself, so the characteristic smell of the fiberglass shop is noticeably absent.

It’s a much more pleasant and cleaner working environment in the shop.

Deck Part





This is the hardtop and front deck for a 40 C Carver that is going into production. The part has been made with vacuum infusion process and is now being held in a steel assembly jig.




Bridge and deck pieces stacked






Upside down on a jig is a flying bridge with other pieces lined up so that they stacked together with the hardtop in the distance.




Upholstery shop




The company makes all of its own upholstery and seat cushions internally to control both production and quality.






 Dry cloth 





Dry fiberglass cloth is applied over the form that has been gelcoated before the resin infusion step. In this nice clean working environment, the glass layers are positioned with care.



Large infused parts 





Here a large part is being prepared for vacuum infusion. Notice the yellow sealant around the edges and the plastic sheet. Vacuum lines are being added through the plastic at this stage.


Vacuum down





You can see from the look of the plastic membrane that the vacuum is sucking the materials down into the mould. The resin and vacuum lines have now been sealed off with clamps and the vacuum will be maintained for a time while the part cures.





Two 40 Carver hulls





A pair 40 Carver hulls are waiting for further assembly.






Stringer system





This is a fiberglass stringer system being held in position on a jig. These hat-section stringers will be turned over and carefully bonded into a hull part to provide strength and stiffness with low weight.




Inner liner





If you ever built model kits as a kid, you’ll realize that you can apply the same thinking to a 40 foot yacht. This is an interior liner section that will give additional strength, a low-maintenance gelcoat finished interior and includes precise and repeatable locations for interior bulkheads and cabinetry.



Men in the hull





This shows some of the bulkheads being inserted, interior hull sections being finished with gelcoat for easy maintenance and the stringer system in position while workers install various mechanical systems.

Seeing it from the catwalk gives a better view of the interior of the Carver 40 coupe under construction.



Woman in cabin 




The woman in this picture is back-sealing the window glass during construction.






Carver 52 Command Bridge





You can see how the very large and modern facility is bright and beautifully organized to turn out an elegant new yacht with quality and precision. Here we see a Carver 52 Command Bridge in the test tank where all the thru-hull fittings and systems are being checked before shipping.



Neptunus 650F Review

Neptunus 650F 400

By Andy Adams

Over the years Canadian Yachting has had the pleasure of doing several boat review articles on new Neptunus models and we are familiar with the qualities that Neptunus is famous for. They have all been exceptional yachts, but this is the one I would most want to own myself. It’s a personal choice and a matter of taste as to whether you would prefer to have a sedan express model or a flybridge but in my opinion, the flybridge layout offers some wonderful attributes.

We met with Neptunus Managing Director Jan Willem De Jong this past fall to take the new Neptunus 650F out in Lake Ontario. 

Read More


The Other Virgin Islands

Sunset off St John

By Mark Stevens

I was first seduced by the United States Virgin Islands during a ferry ride from St. Thomas to Tortola to begin one of our earliest British Virgin Islands charters nearly twenty years ago.

A perfect sunset off St. John with St. Thomas views for backdrop.

Clearing Pillsbury Sound, surrounded by voluptuous emerald mountains as the ferry sliced through royal blue waters, I was struck by the unspoiled ambiance of St. John, the island gliding past our starboard beam and the irresistible charm of a village called Cruz Bay visible from our quarter stern.

Read More