July 11, 2017

Common Gauges

For most of us – this is the time to make the most of the boating season – launch and set up are done. Systems have been recommissioned. Let the fun begin!

Common gauges include RPM, fuel, temperature, oil pressure and battery voltage

But wait……on what should be a relaxing weekend aboard, that thing has stopped working (in this case, ‘thing’ means any part that used to work, but now doesn’t).

 

Let’s look at a few common things:

Batteries: They may no longer accept a charge from an alternator/battery charger, or they don’t hold enough voltage to sustain the electronics that they should. Most marine type batteries for everyday starting and house purposes are serviceable: meaning that they can be tested under load for correct discharge of voltage and reconditioned (usually by adding distilled water to conventional lead-plate style batteries) when they don’t function properly. Before servicing batteries, they should be properly tested by checking voltage (using a multimeter for a base reading), and followed-up by testing the voltage under load (using a battery load tester). Be sure to observe safety precautions and wear appropriate protective devices (gloves and safety glasses). A qualified marine service shop can take care of battery service for you – or you can follow the maintenance procedures available from the manufacturer.
Marine BatteryThis conventional lead-acid marine battery has two ports that can be opened to allow distilled water to be added as part of a reconditioning and maintenance program.

Gauges: RPM, Speed, Fuel, Temperature and oil pressure gauges are common to most boats and are each relatively simple devices comprised of the gauge (the dial that gives the operator information), the sending unit (the part of the engine that provides information to the gauge), and the wiring between the two. It’s a relatively straightforward procedure to test each component: The gauge is tested for power to it, and that it is correctly grounded. The sending unit is then tested (by testing the resistance and/or voltage to and from the unit by using a multimeter). Next, the wiring between the gauge and sending unit is checked and tested to ensure that it is carrying the information correctly between the two. In most cases the engine manual should be consulted for complete testing procedures.

Windows, ports and hatches: over time, they begin to leak! Often an annoyance, sometimes bigger leaks become detrimental to bilge water levels and the integrity of fiberglass. Whichever the case, use an appropriate marine sealant or caulking to seal up any gaps that allow water to enter the cabin. Seals and gaskets around hatches and ports are often an entry point for water and should be replaced when wear is visible. Likewise, hatch frames and hinges will wear, bend and rust which allow the weather in! Ensure that you check the surrounding fiberglass and gelcoat when filling a leak – caulking and sealants can only do so much. When large gaps or fiberglass damage is evident, a proper fiberglass patch may be necessary before caulking or sealing. Consult with your local marine store or chandlery to find the right caulking, sealant or gasketing materials for your application.

Electronics and Navigational equipment: Modern systems can be quite complicated and require factory-trained specialists to diagnose and repair problems. Consult a qualified repair tech to address concerns with electronics and navigation equipment

Trim tabs and stern drives: Movement of drives and trim-tabs is facilitated through hydraulic pressure – check fluid reservoirs to ensure that fluid is at the correct level and top-up as necessary. Many stern drives also have adjustable limit switches which allow adjustment of how high or low the drive will trim. Stern drives have a ‘trim limit switch’ on the side of the drive’s gimbal ring which allows adjustment to the limit that the drive can be trimmed up and down. Two small screws on the trim limit switch can be removed quickly for adjustments – the limit switch is tilted one way or the other to adjust the up and down limit of the stern drive. Your engine or stern drive manual will provide step-by-step instructions on how to do this – or a qualified repair tech can make adjustments to these systems as required.

Bilge Pumps: these devices pump excess water from inside the boat, overboard. Failures tend to occur in two ways: they wear out from overuse or age, or they pick up debris and dirt from the bilge which clogs the pump and burns it out. Keep your bilge as clean and dry as possible, inspect the pump when possible to ensure that the vanes are clear to turn properly and check to make sure that float switches work as designed. If your bilge pump works intermittently or stops working completely, have it serviced or replaced.

Alternator: The alternator charges the batteries as the engine runs and battery voltage should read between 13.5 and 14.5 volts as the engine is running (driving the alternator). If the batteries aren’t charging at this rate, there may be a problem with the alternator. Repairs may be as simple as tightening a belt, or may require wiring replacement or a more complete servicing.

Starter: When the key is turned, battery power turns the starter motor, which turns the boat’s engine and lets it roar to life. Starter motors are simple in design, but require many components working together properly to function as designed. Consistent boat starting problems should be diagnosed by a marine mechanic. Most starter problems are attributed to lack of power in the starter battery – keep it charged and well maintained to avoid problems when the key is turned.

Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program

Related Articles

Destinations

  • Prev
Located about half way between Shediac and the Miramichi on New Brunswick’s Acadian Coast, the town ...
Suddenly the once forsaken city of Hamilton, Ontario is booming for at least two good reasons.
The Salty Dawg Sailing Association (SDSA) invites all sailors to join a cruising rally from the ...
Long popular with New England and St. John area boaters, Passamaquoddy Bay is too often overlooked ...
We did breakfast yesterday in the Greek port of Piraeus, just outside Athens:strong coffee, crisp ...
After much speculation Prince Harry finally popped the question to American actress and longtime ...
Last January we ran a short piece on the motor boat A Great Story which had been restored by the ...
The Moorings has just announced the launch of its newest Caribbean destination, Antigua. 
Toronto sailor and former RCYC coach/sailing instructor Ryan May is now a US coast guard captain ...
Just before the weekly party at Shirley HeightsSunsail staffer Chris Donahue conducts our chart ...

How to be as Polite as a Canadian at Gulf Island Marine Park Anchorages

Gulf Island Marine ParkStory and photos by Catherine Dook

One summer I sold ice cream and knick-knacks at Montague Harbour Marina. I was standing behind the counter one day, when the phone rang. “There’s a boat at anchor in the middle of the bay that’s been playing loud music for three hours,” complained an irate-sounding male voice. “Can you make them stop?”

“Um, no,” I replied. “The marina has no jurisdiction over the anchorage. Besides, my only weapon is a till.” The man hung up on me.

Now when you think about it, you can understand why the poor fellow was annoyed.

Read more about the Gulf Island Marine Park.....

 

 

Lifestyle

  • Prev
We were all set with this week’s POTW when a real stunner came in as part of a story on the Blind ...
Have your say. Send an email to This email address is being protected from spambots. You need ...
When I was about ten years old I starting racing sailboats on Cape Cod and the sound of the wind ...
I took this photo in July 2017 from our boat Ginger which was anchored and stern tied in Mouat Bay ...
Were we nervous when we returned to Adamant 1 in November? The answer would be a hearty yes. The ...
Just to put it in historical time warp I was a World Sailing Vice President 1976-1994 and President ...
Great icicles! This is not what one expects from the tropical climes of BC. It’s a nice winter ...
Rossiter is a Canadian builder in Markdale, Ontario that builds a nice fleet of rowboats and small ...
Welcome to Photo of the Week 2018. If you are not familiar with this wonderful feature (What???!!!) ...
Living the dream! Longtime CY staffer and now blogger Lynn Lortie with her husband Pat left Midland ...
Canadian Yachting Digital April 2018

Boat Reviews

  • Prev
Commodore’s Boats is a full service shipyard with over 50 years of generational history and ...
Cruisers Yachts debuts the all-new 42 Cantius. The sporty, luxury cruiser will make its first ...
Once again, the designers at Jeanneau have outdone themselves with the innovative new Leader 10.5 ...
The introduction of X-Yachts’Xc range in 2008 has proven itself to be something of a game changer ...
Hull #1 ZINNIA, the all-new, twin outboard MJM 35z left Boston BoatWorks on July 5 for Newport and ...
Following a 10-year hiatus, Richmond, BC-based Crescent Custom Yachts is once again launching ...
According to the folks at Fraser Yacht Sales, you couldn't ask for more - the new Azimut Atlantis ...
During those cold, cold, sunless, dreary months of January and February, I want to remember the fun ...
The Rossiter 23 Classic Day Boatis both a logical extension of the Canadian-built Rossiter line and ...
It's rare for Canadian Yachting magazine to report on the same boat twice, but that is how ...

 

Cruisers Yachts Cantius 42

Cruisers Yachts Cantius 42By John Armstrong and Andy Adams 

The latest new model from Cruisers Yacht sis the Cantius 42 and this yacht made its debut in the fall of 2017, at the Fort Lauderdale International Boat Show. We had the pleasure of going all through this newest Cantius there and clearly, the Cruisers Yachts people continue to refine and expand on all the features that have made the Cantius line such a success.

The new 42 continues the Cantius family resemblance with handsome and distinctive lines including a big section of hull side glazing port and starboard that makes the full-beam mid-ship master stateroom feel very bright and open.

Read more about the Cruisers Yachts Cantius 42...

 

 

DIY & How to

  • Prev
In this time of boat show afterglow, many boaters are counting the days until launch. 
Water has a funny way of making its way into a boat: through through-hulls, stuffing boxes, leaks, ...
 Since the initial article of this column we have identified a wide range of apps and ...
Since the initial article of this series we have looked at the iPad and its use as a marine ...
The moment we all dread. It’s a warm sunny day and you’re out for a cruise. Suddenly ...
For most of us – this is the time to make the most of the boating season – launch and ...
Question: Is it possible to mount, protect and charge your iPad during marine navigation. ...
  Is iNavX the superlative marine navigation app?    
Question: Can I buy generic automotive parts or products for my boat, or should they specify ...

Marine Products

  • Prev
We have all had the experience of heading down below on a nice boat only to encounter an unpleasant ...
Last year when this column launched a good deal of time was spent understanding global satellite ...
This article was my first about 10 years ago, and it found it's way to an outdoor editor/writer ...
For a gloomy February we look not only at how an app that works within your phone can be of benefit ...
ZCare Marine, offers effective, eco-safe products to help keep your boat clean. They have products ...
Monaro Marine Ltd. of Richmond, BC, designs and builds its own unique brand of semi-custom 21' to ...
With Garmin it is now possible to use both devices without independently operating two devices with ...
When the Halifax Boat Show opens on February 8th there will be an excellent selection of pontoon ...
The 627 is the largest outboard in world. New cylinder heads and camshaft, an uprated ...
Sirius Signal held a product information session for interested parties prior to demonstrating ...