MSHS Wanda IIIThe once-proud vessel is now indefinitely moored alongside Muskoka Boat and Heritage Centre, the open water she longs to race through tantalizingly close and yet oh-so-far away. No longer quite shipshape, the Wanda III hides under a protective tarp. The plastic is for her own good, keeping the elements from damaging her wooden hull, but surely the elegant boat must feel aching embarrassment that in this year – her 100th anniversary – she should be hidden from view instead of gracefully parading across the lakes.

Photo by Ron Sclater

Wanda III is a boat of immense significance, a fact appreciated by the Muskoka Steamship and Historical Society, which restored the vessel several decades ago and employed her for a number of years as a cruise vessel. “She’s the largest private steam yacht in Canada and one of the finest examples anywhere of the private steam yacht era. She’s also a marvellous piece of machinery,” explains volunteer Ron Sclater.

Randy Potts, who captained her for a number of years, wholeheartedly agrees. “It always registered with me the important history of this fine vessel,” he says. “The larger steamships (Segwun and Wenonah II) curry much attention, however the private yacht of Timothy and Margaret Eaton – well now that is worthy of much attention!”

In her day, Wanda III certainly did attract much attention. When she was built in 1915 for the Margaret Eaton, the wife of Timothy Eaton, Canada’s department-store king, Wanda III was the fastest boat on the Muskoka Lakes. Mrs. Eaton planned her that way – she wanted to go from the train in Gravenhurst to her Ravenscrag cottage, in two hours. 

 Undoubtedly, she was also paying homage to her late husband’s wishes. Timothy Eaton had always wanted to have the fastest boat on the lakes. Indeed, Wanda II was built after the proud businessman lost a race in the original Wanda and vowed never to be bested again. When Wanda II burned in a boathouse fire on Aug. 6, 1914 and a replacement was needed, Mrs. Eaton made certain to make good on her husband’s vow. The new yacht would outclass any vessel in Muskoka.

At the direction Mrs. Eaton, the Polson Iron Works fitted the new yacht with a triple-expansion engine, similar in design though smaller in scale to those being used on Royal Canadian Navy Minesweepers then chasing down German submarines in the Atlantic. These coal-fired steam engines were incredibly powerful, capable of sustained cruising at 20mph and bursts as high as 24mph, unparalleled speeds at the time. The craft’s design complemented her engines in providing peerless performance. The Wanda III has a hull measuring 94 feet long but only 12 feet wide, and a draft of a mere six feet, enabling her to cut through the water like a torpedo. The technology that went into her design was, at the time, cutting edge.

Potts remembers well how her unique characteristics made her a handful to pilot. “Her long, slender hull and quick speed made for a few challenges when it came to ship handling,” he recalls fondly. “Turning a boat around of this size or maneuvering for a dock or the locks at Port Carling meant that a bit of thought needed to be done in advance. I always likened Wanda III to a thoroughbred race horse. You need only a little bit of throttle to achieve results. Heavy hands on the steam throttle would only get you in to a mess very quickly.”

Wanda Old

Speed and hull shape weren’t her only distinguishing characteristics, however. Wanda III was also beautifully outfitted with the finest materials money could buy, a yacht worthy of one of the richest families in Canada. She could carry 24 passengers in her elegant mahogany-and-brass salons, where the Eatons enjoyed afternoon tea on their way up the lakes. She cost $34,574.

 (Photo courtesy the Muskoka Steamship and Historical Society) This photo is from Barnesdale in the 1920s, providing a scale shot of the Wanda III alongside the steamship Sagamo. Though she was the largest yacht on the lakes, she was dwarfed by the passenger steamships of the era.

Wanda III became an integral part of Mrs. Eaton’s cottage lifestyle. Visiting musicians would perform on the after deck in the early evening, and many afternoons were spent hosting guests from neighboring cottages aboard for tea-time cruises (a strict Methodist, no drinking or smoking would be permitted aboard). Mrs. Eaton provided the yacht’s captain and engineer with cottages near Windermere so they could be nearby whenever the whim came over her for an excursion.

Despite the good times, the Wanda III suddenly fell out of favour with the Eatons and in 1927 was quickly sold off. What happened?

It was a tragic story. In 1927, a desperate call reached the Eatons at Kawandag. A young girl at Ravenscrag had taken ill with severe appendicitis. She was in desperate straits and had to get medical attention as soon as possible. The Wanda III was her best hope. There were faster craft available – motorboats had now appeared on the Muskoka Lakes, and the Eaton family alone owned several of the most powerful – but in the young girl’s condition comfort was as important as speed lest the appendix burst.

The Wanda III was ordered to raise steam and race the child to Bracebridge Hospital as quickly as possible. Even at best speed the trip took five or six hours, and sadly the girl died en route. Mrs. Eaton was shattered by the news. Whereas once she cherished the family yacht now she could hardly bear to look at her, and she never forgave it. Hoping to distance herself from the painful memory, she sold the Wanda III to Charles Orlando Shaw, the owner of the luxurious Bigwin Inn.

In 1930, the yacht was taken overland to Lake of Bays and became the hotel launch for Bigwin. For 15 years, she took wealthy guests on excursions around the lake but in 1944 the Wanda III’s passenger certificate was revoked. Now without purpose, she languished at the docks at Bigwin for a number of seasons. Wanda Today

In 1948, Wanda III was sold to Cameron Peck, who deserves credit for saving her from an early demise. Peck cared strongly about the loss of early marine history in the area and set about saving of much of it as he could. After purchasing the boat to prevent it being scuttled, he did what he could to preserve and restore her.

 Photo courtesy the Muskoka Steamship and Historical Society) The Wanda III as she appeared when she was owned by the Eaton family, playing host to high teas and musical recitals, while sailing passengers around the lakes.

The yacht subsequently changed hands several times, and for most of the next 40 years was neglected. The Wanda III eventually ended in the hands of Sandy Thompson, an engineer who managed to keep the ship’s venerable machinery operating successfully. The task was bigger than one man, however, and so in 1993 Thompson donated her to the Muskoka Steamship and Historical Society.

The MSHS was which determined to restore their newest acquisition to its former grandeur. Frederick Eaton, the great-grandson of Sir Timothy Eaton, was named the honourary chairperson of the fundraising campaign in 1993 which raised $650,000. By 1996, after many years of decreptitude, the Wanda III was restored and recommissioned in a ceremony presided over by Prime Minister Jean Chretien. It was a proud moment. Once again, she was one of the grand old ladies of the lakes.

In the years that followed, Wanda III joined the Segwun and Wenonah II in carrying countless passengers on memorable sightseeing cruises. Summers were busy with parties for weddings and anniversaries, dinners, cocktail parties and business-reception dinners.

Age eventually caught up the venerable boat again. In August 2000 the boiler, then 85 years old, sprung a leak through one of the bolts which held the angle iron for the floor. Upon further inspection it was discovered that there were likely other cracks in the boiler. Rather than repair it, a new boiler, costing $210,000, was installed to extend her life into a new century, though this replacement did not have the capacity of the old boiler. Further restoration came in 2004 when the Society replaced her entire hull at total cost of $200,000.

Sadly, however, a decade later the historic yacht is once again hardly in shipshape. “Wanda III was withdrawn from passenger service a number of years ago due to regulations and needs significant restoration work.

“The problem is Wanda III needs a boathouse to keep her out of the elements. Sun, snow and rain isn’t good for wood varnish,” explains Sclater, who served aboard her for a number of years in the late 1990s and early 2000s, including a memorable stint as Captain.

There were plans to build a private boathouse to store the Wanda III and other vintage vessels the Society was hoping to acquire. This boathouse was intended to be part of the original Muskoka Wharf project and was to be attached to the Muskoka Boat and Heritage Centre. Unfortunately, the idea fell through when the Northern Ontario Heritage Fund Corporation reneged on $2.5 million in promised funding as a result of Muskoka being taken out of Northern Ontario.

As a stopgap, the Society invested in a shrink-wrap cover at a cost of $40,000 which, Sclater explains, will allow work to be done while still protecting the vessel from the elements.

“In today’s world of dollars and cents, her math did not add up,” says Potts. Quite expensive to run and quite expensive to maintain, Wanda III remains an anachronism in today’s world. A symbol of Canada’s wealthiest merchant family and a symbol of an era, and a shining example of Canada’s shipbuilding history and Polson Iron Works workmanship, it’s important that she be preserved if only for future generations to understand what yachts of this stature were like.”

The Muskoka Steamship and Historical Society is committed to doing just that. “The Society’s Board of Directors recognizes the importance of her restoration,” explains John Miller, General Manager of Muskoka Steamships, “and has begun steps to return her to her former glory.”

Hopefully one day soon this majestic and historically significant yacht will again be seen sailing gracefully across the Muskoka lakes, allowing our imaginations to cast back to that elegant era of a century past when Mrs. Eaton hosted high teas and concert recitals afloat.

You can wish the Wanda III a happy centennial by joining the Friends of the Wanda III (contact Ron Sclater at This email address is being protected from spambots. You need JavaScript enabled to view it.) and keep abreast of plans to secure her future. 

 

Destinations

  • Prev
In the 1920s, a small cove in Canoe Bay was used as a shipping point and safe-haven for rum runners ...
Here’s an update from Caroline Swann with some news for the adventurous types who may be heading to ...
The New Glasgow marina is located about six miles up the East River of Pictou in the heart of the ...
The British Virgins took a huge hit last fall from Irma. Boats were stranded on the shore by the ...
Located about half way between Shediac and the Miramichi on New Brunswick’s Acadian Coast, the town ...
Suddenly the once forsaken city of Hamilton, Ontario is booming for at least two good reasons.
The Salty Dawg Sailing Association (SDSA) invites all sailors to join a cruising rally from the ...
Long popular with New England and St. John area boaters, Passamaquoddy Bay is too often overlooked ...
We did breakfast yesterday in the Greek port of Piraeus, just outside Athens:strong coffee, crisp ...
After much speculation Prince Harry finally popped the question to American actress and longtime ...

 Killarney

KillarneyStory and Photos by: Jennifer Harker

We’re aboard Attigouatan, a Pursuit 2260 that normally lives life as a friend’s cottage boat, running back and forth from dock to dock. This will be her longest run in four years, travelling the approximately 120 kilometres (80 miles) northwest from Parry Sound to Killarney, threading our way through the northern reaches of the stunning 30,000 Islands of Georgian Bay’s eastern shoreline.

Her name evokes an early indigenous name for Lake Huron – Spirit Lake. 

Read more about Killarney....

  

Lifestyle

  • Prev
This photo from a CPS member shows how talented boaters are. Brenda Cochrane from Kelowna BC, a ...
The first part of this blog will show that not every day is blue sky and sunshine in the Bahamas!
This beauty came our way from Reel Deal Yachts in Bahia Mar, Florida. Why not charter for the ...
This new legislation from Washington State Department of Fisheries applies to boats launched in ...
Don’t miss this brilliant photo double header
In honour of Launch Day, our POTW this time comes from Wendy Loat in Port Credit. This shot, taken ...
Our favorite, Man-O-War Cay, is home to the Albury Boat Building empire. They have been building ...
On the Easter Weekend, the Sidney North Saanich Yacht Club from Vancouver Island, had its first ...
We were finally able to get a SIM card and data plan on our phone Monday morning. We could now ...
It’s Friday afternoon at the Newport Yacht Club in Stoney Creek, and that can only mean one thing - ...

Boat Reviews

  • Prev
At the boat shows, the Ranger Tugs’ classic tugboat lines always grab the crowds, with the wives ...
Tactical Custom Boats announces the sale to a North American client of a custom Tactical 77’ – Fast ...
Bruce Elliott is an inventor. And when he sold the technology he developed to build utility poles ...
One often asks of a winning achievement or a fabulous design, could it have possibly been done ...
The latest new model from Cruisers Yachts is the Cantius 42 and this yacht made its debut in the ...
The Sabre 45 Salon Express is new for 2017, making its debut at the Fort Lauderdale International ...
Jeanneau’s newest NC model is the NC 33, and it’s an exciting and innovative inboard cruiser ...
The Four Winns H290OB combines two of the most popular new big boat trends to come up with a great ...
Commodore’s Boats is a full service shipyard with over 50 years of generational history and ...

 

Jeanneau Sun Odyssey 440

Jeanneau Sun Odyssey 440By Zuzana Prochazka

There are few things more satisfying than watching someone thumb their nose at tradition and introduce something revolutionary that kicks convention to the curb. French designer, Philippe Briand, has done just that for Jenneau’s new line of Sun Odyssey family cruisers. By starting with a clean sheet, Briand re-thought how we move about on deck and below, and the results on the Jeanneau 440 are game changing.

Jeanneau unveiled the first hull of their 440 in Annapolis with dramatic flair. On command, the plastic that sheathed half the boat...

Read more about the Jeanneau Sun Odyssey 440....

 

 

DIY & How to

  • Prev
CYOB readers often ask questions about their boats and system. For this issue, I’ve answered a ...
Modern marine engines run at very high temperatures and rely on a few methods to keep their ...
Pyrotechnic distress flares have been around for decades, while electronic strobe distress flares ...
In the early spring, just after launch, with the hustle and bustle of engine checks, antifouling, ...
All engines, including marine engines (inboards, outboards and stern drives) have many moving parts ...
Most of us don’t give a second thought to our sacrificial anodes – those curious knobs of raw metal ...
I once heard an argument at a yacht club. Two old salts, patiently itching to let go lines and ...
In this time of boat show afterglow, many boaters are counting the days until launch. 
This one-day course consists of both theory and practical demonstration sessions, is designed to ...
Water has a funny way of making its way into a boat: through through-hulls, stuffing boxes, leaks, ...

Marine Products

  • Prev
Canada Rope promises that its new Night Saver Rope will illuminate at night and act as a reference ...
Take a look as a 68-foot yacht docks itself in between two Volvo Ocean 65 sailing yachts at the ...
Industry Firsts Include Direct Injection and Integrated Electric Steering System
Verviers, Belgium, 18 May 2018 — Mercury Marine, the world leader in marine propulsion technology, ...
Again, we return to the beginning. We started this column with a look at marine navigation for ...
Ga-Oh (spirit of the winds in Algonquin) creates bags and other items from re-purposed sails.
The 2018 Northwest Boat Travel Guide just arrived. This time of the year is the perfect time for ...
We are all looking to gain a little more time these days, and technology is often the route we ...
While they are no longer a part of the CPS Flare Program, Fogh Boat Supplies and Fogh Marine, both ...
We have all had the experience of heading down below on a nice boat only to encounter an unpleasant ...