Contessa32250BBy Paul Howard

When British naval architect, David Sadler, drew the lines of this design in 1972, he gave the Contessa 32 a unique profile. At a time when cruising boats sported springy sheer lines, this racer/cruiser appears at least at first glance, to have a reverse sheer. In fact, the bow is higher than the stern, with the lowest part of the deck just forward of the cockpit. Other distinguishing features of the Contessa 32 are long overhangs, a narrow, tucked-up stern, low topsides and a narrow beam to length ratio. Below the waterline, Sadler has penned a moderate fin keel, with a skeg-supported rudder on a deep vee cross-section. In Britain, the Contessa was built at the Jeremy Rogers Boatyard, and was voted "Boat of the Show" at the 1973 Boat Show in London, England. Based on this initial success, the Rogers yard in Lymington went on to manufacture over 700 boats between 1973 and 1982.

In 1973, J.J. Taylor president, Alan Nye Scott, had a Rogers-built hull and deck shipped from Britain so that Taylors could produce a set of moulds for Canadian production. The Contessa was an instant success, and when the production run ended in 1990, 87 32s had been built.

Offshore cruisers will be interested to know that the fibreglass lay-up of the Canadian-built 32 meets the same Lloyd's specifications as the British boats. Boris Sam, who joined J.J. Taylor in 1970 to build the Contessa 26, comments on the 32's robust construction. "The hulls were constructed in two halves, with the gelcoat and a layer of 1.5 oz. mat. Above the waterline we used three layers of 18.5 oz. Fabmat.

"Below the waterline we added an additional layer of 18.5 oz. Fabmat, followed by another two layers at the keel, and with five layers of the same mat added at the chainplates for the shrouds and backstay. Next, the entire laminate schedule was covered with another layer of 1.5 oz. mat."

Lastly, as Sam explained, the two halves of the hull were joined with another five layers of mat. "It's hard to believe the amount of fibreglass that went into that boat!" said Sam, who now lays up power boat hulls at Medeiros Boat Works in Oakville, Ont.

The primary difference between the Canadian and British models is in the interior. While the overseas boat had an all-wood finish down below, J.J. Taylor used white fibreglass headliners, as well as mouldings for the galley, head and main salon furniture, which was finished with wood trim. Consequently, the Canadian boat was slightly lighter in weight, the interior brighter, and production time shorter.

Declan Mackell, a transplanted Irishman who now lives in Etobicoke, Ont., bought Sean-ois (Gaelic for Mother of Wisdom) in 1975. In July 1977, he sailed away on a 50,000 mile, single-handed circumnavigation, before returning to Toronto in 1983. He carried no furling gear, but with 12 sails in the lockers, he often poled-out twin running sails in the Trade Winds. Mackell reports his best day's run was 186 miles, on the Canary Islands to Barbados passage. "I didn't touch the helm for 14 days," he said, "as the twin sails and wind vane did all the work."

The toughness of the Contessa hull was tested on Mackell's world tour when he ran into a 40-foo whale. Mackell was cooking below during the daytime, as his boat charged along at six to seven knots, when there was a loud noise, and the boat rolled violently to its beam ends. When Mackell came on deck, the obviously stunned whale lay momentarily at the surface near the boat before it swam off. Remarkably, at the point of impact there were no more than a few lines of crazing in the gelcoat at the waterline.

In another episode, Mackell was asleep in his bunk when a cargo ship passed so close to him that the freighter's bow wave filled the jib and broke the forestay. After he was thrown from his bunk, he scrambled topsides to jury rig so he could sail to his next destination." Sean-ois was displayed in the 1984 Toronto International Boat Show, when Mackell joined the crew at J.J. Taylor. Today this circumnavigating 32 is based in Sault St. Marie, Ont.

Mackell later bought another Contessa 32, Ashlin, launched in 1989. Modifications were made to make the boat lighter and more airy. He used no teak in the interior, added a mid-ships hatch in the coachroof, made the forward bulkhead only partial between the head and the vee-berth. Other modifications included filling all the cavities, including the cockpit coamings, behind the liners and other inaccessible areas, with foam insulation.

Readers of Adlard Coles' Heavy Weather Sailing (International Marine) will be familiar with the remarkable sea-keeping qualities of a British built Contessa 32 that raced in the infamous Fastnet Race and gale of 1979. Of the 303 starting yachts competing in six divisions, only 85 finished. In a period of nine wind-whipped hours, 15 lives were lost, five yachts sank, and a further 19 were abandoned. Much of the Fastnet was sailed in 35 to 40 knot winds, with several hours of mean speeds of 55 knots, gusting to 65 knots or higher.

The Contessa 32, Assent, was the sole yacht of the 58 starters in the (smallest) Class to finish and, as Coles writes, "put in a very good corrected time in relation to her size." Assent was a sailing school boat, with one instructor and four students aboard. Coles relates that it drove to windward at about 60 degrees off the wind, doing about four to five knots, luffing up to the crests, then bearing away in the troughs. At one point, the boat was knocked down, and its mast head was in the water for about 10 seconds before it righted itself. Coles writes that the crew did well with "...high morale...plenty of sleep and light meals which could be taken easily, mostly carbohydrates -- bread and honey, flap-jacks, all washed down with fruit drinks.... Assent had no electronic instruments; distances were recorded on an ordinary Walker's log streamed from the taffrail."

The cockpit of the Contessa 32 is long and comfortably arranged, with high backrests and excellent protection from the elements. Tiller steering was standard, though most boats have wheel steering. The side decks are wide, and the fore deck is clear and easy to work on. The bow comes to a very sharp point, with a long overhang forward.

The interior of the Contessa 32, however, is a disappointment to those expecting to find roomy and airy accommodations. After all, this is a early-70s British design. Although the boat has a stated headroom of 6 ft. 1 in., this height is only found at the foot of the companionway; beyond this spot, headroom quickly reduces to about 5 ft. 10 in. in the main salon. The galley is immediately to port, at the foot of the companionway, with a decent number of cupboards and stowage, and adequate counter space. Early models had an L-shaped galley, while later models (from 1982 onwards) had more of a U-shaped dinette, with seating for four or five that converts to a smallish double berth. A single settee/berth sits opposite this dining area. Forward, a narrow head, with stowage opposite, divides the main salon from the companionway.

Early boats were fitted with a 24-horsepower Farymann diesel, although in later models the Bukh 20-horsepower was standard. Various other boats were outfitted with the Volvo 2003 28-horsepower, or the three-cylinder Yanmar diesel.

When Terry Kirkland won a small lottery prize he decided to buy a Contessa 26. A few years later, when he won a second larger lottery jackpot, he purchased a Contessa 32. Gerta Woodbury bought Kirkland's Contessa 26, Millennium, which she sailed on Lake Ontario for several years. When she heard Kirkland was ill with cancer, Woodbury flew to Vancouver to visit, and cruised on the Contessa 32, Millennium II, while there. After their sail, Kirkland insisted that Woodbury should have his second Contessa, which he willed to her. Financial arrangements to purchase the boat from the estate were made. Sadly Kirkland died five days after her departure. After it was trucked from Vancouver to Toronto, Millennium II began its new sailing life at the Mimico Cruising Club in Etobicoke, Ont.

"I really like the low freeboard and solid feel of the boat," said Woodbury. "I gladly sacrifice interior volume for that sense of security." And at 5ft. 2 in., this skipper reports that she has plenty of room for her needs.

Originally published in Canadian Yachting's Summer 1996 issue.

Specifications

LOA - 32ft.

LWL - 24 ft

Beam - 9 ft 6 in.

Draft - 5 ft 6 in

Ballast - 4600 lbs

Sail area - 417 sq ft

Engine - 20 hp Bukh

Berths - 5

Lifestyle

  • Prev
We crossed Lake Ontario from Oswego with a minimum of fuss and did a little happy dance when we ...
Our Photo of the Week comes from Mark and Lisa Harris who winter in Vancouver, Washington and spend ...
I am new to boating. Bought a 2019 Ranger Tug in April followed by taking a short boating course ...
Arie and Maribeth sent us this photo from their honeymoon departing Killarney…I think they were in ...
This shot was taken last week by Jessica Lee, a freelance photography pro, Albacore racer and part ...
On a sunny and windless day we led Alicia and another sailboat into New York Harbour. There were ...
It was a trip 2 or 3 years ago, and all 4 boats traveled up to the Killarney area in a ...
My name is Alexandrine GOVAN, mother of a 5 years old girl and I found your contact on internet. ...
John Booth, who passed away just a few weeks ago was one of the most amazingly gifted and ...
We left Vero Beach on Saturday morning with Alicia, a boat from Sweden, following close behind. The ...

DIY & How to

  • Prev
The new editions of PORTS Cruising Guides, from the publishers of Canadian Yachting will be ...
As the seasons change and we move from warm summer into cooler fall, many fanatic boaters ...
On the Friday before a weekend with a gorgeous forecast, I heard on the news that a boat had ...
A reader suggested we take a look at anchors. Anchoring seems simple enough. A weighted hook with a ...
If you’ve spent any time in a boat yard during spring commissioning season, you won’t find it out ...
As a busy marine mechanic, I tend to have the same or similar conversations often, and they’re ...
This time of year, great deals abound. That boat with the ‘for sale’ sign looks quite attractive. ...
For less than US$2,500, Jim Leshaw, a lawyer who lives and works in Key Biscayne, Florida, ...
Each spring, I tend to notice canvas. I wish it was because it’s been immaculately maintained and ...
I’ve had two emails over the past few weeks with a count-down to launch (47 days per the last ...

Leasing a YachtBy Andy Adams

When I first saw the display at the Toronto International Boat Show saying that you could lease a new yacht, it stopped me dead in my tracks. While I had never considered leasing boats, we are certainly seeing growth in boat rental organizations, so leasing didn’t seem out of line. In fact, I wondered why it had taken this long to see boat leasing come to the market.

However, I have a reasonable understanding of how leasing works compared to financing a purchase and I wondered how the numbers could work for something like a yacht. The sign was in front of a 60 foot Princess Express Cruiser – about $3,000,000 

Read more about Leasing a Yacht............

 

  

Boat Reviews

  • Prev
The Canadian Yachting test crew last week had the opportunity to run the Bavaria S36 HT at St ...
ILCA is seeking new builders to complement its existing network of manufacturers, the International ...
Nelson Gilbert (1854-1921) began building canoes in Brockville in the 1890s, a time when the sport ...
I have heard a lot of talk lately about trends in yacht clubs where senior membership is getting ...
To get you in the mood for cruising the Boat Show then launching in spring, here’s a boat that ...
Quite simply, the styles of boats have changed. Where in past years a buyer might have been looking ...
At the boat shows, the Ranger Tugs’ classic tugboat lines always grab the crowds, with the wives ...
Sometimes a great idea requires an encore, and French yacht builder Jeanneau got that with the ...
Tactical Custom Boats announces the sale to a North American client of a custom Tactical 77’ – Fast ...
Bruce Elliott is an inventor. And when he sold the technology he developed to build utility poles ...

J99By Katherine Stone

All set to pull out the Code 0 before dousing the jib.

It was a very cold and wet beginning to the summer and we never thought it would arrive in Southern Ontario. Doing a 100 miler race on Lake Ontario (billed as the COOLEST race on the lake) with my 8 layers of thermal clothing, woolen ski toque and ski mittens, along with a neck warmer kept me on the edge all night, just out of frostbite reach. I shouldn’t have complained, as we also had wind!

July and August arrived, and it has certainly warmed up, in fact, its too warm, AND we don’t have wind. We are now counting 5 Wednesday nights in a row without wind to race. 

Read more about the J99 Offshore Shorthand Speeder.....................

 

Wellcraft 242 FishermanBy Andy Adams

Boat buyers are gravitating to the latest centre console boats for a wide range of reasons but for the Wellcraft 242 Fisherman, you can sum it up by saying it’s about features, style and value.

This great-looking boat is just as capable on a family picnic cruise as it is doing serious blue water fishing. A wide range of options let the buyer tailor the boat for their specific interests, but it’s all there to choose from. Our test boat was well-equipped for that comfortable cruise with easy access via the swim platform and through the transom gate into the cockpit.

Read More about the Wellcraft 242 Fisherman..................

Destinations

  • Prev
Provincial Boat Havens are those special places to drop anchor in British Columbia’s West Coast and ...
NW Explorations, a Bellingham, Washington-based yacht charter, brokerage, and marine services ...
If you haven’t cruised the Rideau Canal before, you have missed a special treat and even if you ...
At the 2019 Vancouver International Boat Show I had the pleasure of meeting up with Allyson and ...
Following the harsh impact of Hurricanes Irma and Maria, The British Virgin Islands is making an ...
For the adventurous boater Bunsby Marine Provincial Park is a special place, situated due south of ...
There is good anchoring in Cowichan Bay and nearby, and salt water enough to make any boater happy. ...
We’re gliding through green-blue waters, colours so vivid and bright they hurt your eyes. We’re set ...
The Halifax waterfront has been attracting more and more large yachts in recent years. However, a ...
Ah Canadian simplicity at its finest; small town, big marina. Little Hilton Beach (population ...

Port Severn's Lock 45Blake Marchand


As the final link between Lake Ontario and Georgian Bay, Port Severn’s Lock 45 is the gateway to the beautiful Trent-Severn Waterway. The first and smallest lock to be constructed on the Severn portion, Lock 45 is entrenched in Canadian History and is worth the trip in itself. However, it is the waterway and its idyllic surroundings that will keep you coming back.

The canal connects Lake Ontario and Lake Huron with an eastern terminus in Trenton and a western terminus in Port Severn. Its amazing natural waterways include the Trent River, Otonabee River, The Kawartha Lakes, Lake Simcoe, Lake Couchiching and Severn River.

Read more about Vancouver...........

 

Marine Products

  • Prev
Navigating the process of yacht care and maintenance just got a whole lot easier, following the ...
I will be honest, I am generally not a big fan of Sport Utility Vehicles (SUV). My wife and I own ...
In the April 2015 edition of CY magazine, I published an article on anchors and anchoring – Staying ...
The Seabin device part of the Oak Bay Marine Group trial, has had promising results so far while ...
When I took the Mitsubishi Outlander PHEV down to Wednesday night racing, the people that came over ...
Protecting your boat from scratches and dents isn’t always easy. That’s why the Big Bumper Company ...
Rancho Santa Margarita, CA - Forespar has just introduced a new smaller size version of their ...
As boaters we all have a very unique connection to the water and all the opportunities it presents. ...
Edited by the Quebec Marine Association under the direction of L'Escale Nautique (producer of the ...
Blue Guard has announced the general availability of the BG-One, a solid-state bilge pump switch, ...