Sept 13, 2018

Fresh Water HandlingAn accumulator tank allows pressure to be built up for immediate use taking some work off of the fresh water pump. It’s not on every boat - but is a helpful device for consistent pressure.

Nothing stops a vacation faster than a problem with the fresh water system – be it leaks, smells, plugs or loss of pressure! Any of these can make living aboard for more than a day-trip strenuous, and in many cases can take the joy and comfort out of being aboard.

A typical water system incorporates multiple elements:

Deck inlet – a fitting on the deck marked ‘Water’ is where water can be added (via hose from shore) into the boats water tank

Water Tank – water added to the deck inlet occupies space in this tank

Fresh water pump – a pump that pressurizes the system, drawing water from the tank, and pushing it to the faucets. Typically an electric pump, found on the 12V/DC panel. The pump is designed to run until the system is pressurized, then shuts off automatically. Once pressure is released, the pump will turn back on, keeping the pressure constant.
Piping – can be flexible or rigid plastic. Increasingly, I’ve seen PEX tubing as a cost effective solution. Piping is typically colour coded – blue, or blue stripe for cold water lines, and red/red stripe for hot water

Hot water tank – a tank that heats water using electricity. Hot water tanks are typically 110V and found on the AC panel

Faucets – usually found in two or more locations aboard: the galley and head are most common.

Head – a marine toilet. The most common is a unit that includes a lever to both pump water into the bowl after use, and to pump waste out into a holding tank

Waste Tank – a holding tank for waste from the head

Waste deck fitting – where a shore-based pump can be attached to remove the waste from the waste tank (called a ‘pump out’)

Each part of the fresh water system is straightforward, simple and cost-effective to upgrade and maintain. Where do things go wrong? Here are 4 examples:

1) Leaks – because the system is pressurized, fittings and connections must be tight and sealed. Over time, connections can loosen and require re-sealing. Additionally, especially in the pump and in the head, seals can loosen and O-rings can shrink, causing leakage. Luckily, manufacturers of both marine toilets and water pumps have servicing kits available to replace worn parts. In areas where connections have loosened, either replace the connectors, or re-tighten using Teflon tape.

2) Smells – sitting water and waste will allow bacteria to grow, especially aboard a hot boat in the summer! Water tanks and lines should be periodically flushed out and cleaned (there are a number of products available that can be added to fresh water tanks to kill bacteria in both the water and hot water tanks).

3) Loss of pressure – typically associated with a leak somewhere in the system: a faucet that doesn’t close all the way, a hot water tank drain valve left open, a seal in the head pumping mechanism, or a faulty water pump are common causes.

4) Blockage – ‘gunk’ in the water tank (or from sea-water if the head draws from a seacock), and too much toilet paper are the most common causes! A few preventative tips: make sure that there is a strainer between the water tank and water pump to remove any gunk. If the head draws in seawater, a strainer can be fitted here, too). Use marine-grade, biodegradable TP – it breaks down easily and won’t cause blockages (at least not as many).

Winterizing/layup:

It’s important to winterize the fresh water system by draining all of the water and by running antifreeze through each component to ensure that it is protected from freezing damage. Here are a few basic steps to take:

1) Drain the water tank – turn on the water pump, and open all the faucets until no more water drains. Turn the water pump off.

2) Drain the hot water tank and disconnect the lines – hot water tanks have both a pressure release valve and a drain – open the drain until water is gone. Next – remove the two hoses the bring water TO the hot water tank, and exit FROM the hot water tank. Find an appropriate connector to connect these hose together. This creates a loop, so that any antifreeze that is pumped through the lines wont enter the hot water tank – antifreeze will damage the heating elements in the water tank – don’t skip this step!

3) Located the water pump and disconnect the line from the water tank. Replace this line with a new hose running to a bucket full of antifreeze. Close faucets (hot and cold) and turn the water pump on. The system will pressurize with antifreeze. Open the cold and hot faucets in turn until antifreeze is seen pouring out. Close the taps and turn the water pump off.

4) Drain water from the head using the hand pump. Pour antifreeze into the bowl and pump it through. Pour more antifreeze into the bowl and let it sit.

5) Some systems are more complicated – with shore inlets, electric heads, macerator pumps, shower pumps etc. These systems will require a more complicated winterizing plan. Make sure to tailor a plan to suit the systems on your boat.

Despite the end of summer vacation, there’s still great weather for boating – Enjoy!

Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.

Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

Related Articles

Destinations

  • Prev
Following the harsh impact of Hurricanes Irma and Maria, The British Virgin Islands is making an ...
For the adventurous boater Bunsby Marine Provincial Park is a special place, situated due south of ...
We’re gliding through green-blue waters, colours so vivid and bright they hurt your eyes. We’re set ...
The Halifax waterfront has been attracting more and more large yachts in recent years. However, a ...
Ah Canadian simplicity at its finest; small town, big marina. Little Hilton Beach (population ...
Vancouver-based Big Blue Yacht Charters Worldwide owner Emma Murdoch explains that luxury crewed ...
In the 1920s, a small cove in Canoe Bay was used as a shipping point and safe-haven for rum runners ...
Here’s an update from Caroline Swann with some news for the adventurous types who may be heading to ...
The New Glasgow marina is located about six miles up the East River of Pictou in the heart of the ...
The British Virgins took a huge hit last fall from Irma. Boats were stranded on the shore by the ...

Mediterranean Shakedown: A Summer Cruise in Spain

Mediterranean ShakedownBy Sheryl and Paul Shard

This summer my husband, Paul, and I bought our fourth offshore cruising boat, a new Southerly 480 built by Discovery Yachts in the UK. It’s a unique boat with a retractable variable-draft swing keel giving you the option of sailing with a deep draft of 3.1 metres when the keel is down or just less than a metre with the keel fully retracted. Southerly Yachts are great for bluewater sailing and also for gunkholing in shallow creeks and inland waterways. You can even dry them out at low tide so they are is the perfect boat for the type of exploring we like to do. Our new boat, Distant Shores III, is the third Southerly Yacht that we’ve owned over 29 years of international cruising to destinations in the Caribbean, Mediterranean, Middle East, UK, Scandinavia and South America. This boat we plan to sail to the South Pacific.

Read more about the Shards' cruise in Spain...

 

Lifestyle

  • Prev
This issue, to kick off 2019, we have an unofficial Photo of the week and this, the unofficial ...
Readers give us a bit of feedback on the 60th anniversary of the Shark 24
We are home for Christmas this year. Soon we will be heading back to Adamant 1 for another winter ...
This past October we drove to Telegraph Cove with friends and spent a day of wonder cruising the ...
We have kept our subscription to Canadian Yacht Onboard as we have traveled the South Pacific over ...
Stuart Walker a legend in competitive sailing passed away on November 12, 2018 in Annapolis. Stuart ...
“In Grenada, we had about 80 cruiser kids visit our boat...by dinghy of course! Sometimes you ...
Austin Edwards told students and parents at the Saanich School’s “Parents as Informed Partners” ...
As the sole arbiter of the Photo of the Week I, your editor, get to make the choice. This week, ...
Michele Stevens pointed us to this interesting project which recently came to fruition in Cape ...

Boat Reviews

  • Prev
To get you in the mood for cruising the Boat Show then launching in spring, here’s a boat that ...
Quite simply, the styles of boats have changed. Where in past years a buyer might have been looking ...
At the boat shows, the Ranger Tugs’ classic tugboat lines always grab the crowds, with the wives ...
Sometimes a great idea requires an encore, and French yacht builder Jeanneau got that with the ...
Tactical Custom Boats announces the sale to a North American client of a custom Tactical 77’ – Fast ...
Bruce Elliott is an inventor. And when he sold the technology he developed to build utility poles ...
One often asks of a winning achievement or a fabulous design, could it have possibly been done ...
The latest new model from Cruisers Yachts is the Cantius 42 and this yacht made its debut in the ...
The Sabre 45 Salon Express is new for 2017, making its debut at the Fort Lauderdale International ...

Beneteau Antares 27

Beneteau Antares 27By Andy Adams and John Armstrong

You have to love it when something exceeds your expectations on so many levels; the new Antares 27 from Beneteau looks to me like that sort of all-around overachiever.

This is a brand new express cruiser design. With twin Mercury 200 V6 outboards, it delivers impressive performance, a reassuring and comfortable ride, and a level of versatility that will enable this boat to be your vacation partner for all sorts of adventures.

Read more about the Antares 27...

 

 

 

 

Hanse 388

Hanse 388By Katherine Stone

The Hanse group produced their second most popular boat of all time with the Hanse 385. The trick was to build on that winning formula when they upgraded to the Hanse 388, which they have done in spades. The German build quality is first rate and true to the Hanse tradition. Leaving the hull the same with a steep stern and straight stem for an optimal long water line, they went with a slightly stiffer, heavier displacement, new deck, interior layout and window line. Hanse’s highly experienced yacht construction team, judel/vrolijk & co., have combined ease of sailing, comfort and performance into the newly designed Hanse 388.

Read More about the Hanse 388...

 

 

 

Marine Products

  • Prev
While the basics of boat hull design hasn’t changed that much over the years, the same cannot be ...
Yamaha targets the Canadian big-water market with its high-torque 425 horsepower V8 XTO outboard, ...
Looking for a great Christmas gift for the Offshore sailor on your list? This being a Marblehead to ...
Sail shape is long gone. They have stained, feels thin and you see broken threads everywhere. Your ...
Stripping the antifouling paint from the bottom of a boat is physically demanding and is one of the ...
The 2019 Ultimate Sailing Calendar highlights the drama and excitement of blue-water sailing, as ...
Weather nerds and boaters of all stripes will be absorbed by Bruce Kemp’s account of the monstrous ...
Canada Rope promises that its new Night Saver Rope will illuminate at night and act as a reference ...
Take a look as a 68-foot yacht docks itself in between two Volvo Ocean 65 sailing yachts at the ...
Industry Firsts Include Direct Injection and Integrated Electric Steering System