July 12, 2018

Shift Cablean example of a shift cable - note that the ends are manufacturer specific, and come in various lengths.

CYOB readers often ask questions about their boats and system. For this issue, I’ve answered a common question about engine control cables. Please send any questions to: This email address is being protected from spambots. You need JavaScript enabled to view it.

How do I know when I need to service the control cables on my boat?

upper and lower shift cablesEvery boat is unique, and cables aren’t always used the same way, or routed in the same fashion. But here is a breakdown of the types of cables used on both power and sail boats, including inboard, outboard and stern drives:

a) The shift control cable – this cable runs from the helm controls to the engine or transmission and uses a push/pull movement to move the boat from neutral into forward and reverse

b) The throttle control cable – this cable runs from the helm controls to the throttle control on the engine (in a gas engine, this connects to the carburetor. On a diesel, this connects to the injector pump). In each case, in very simple terms, by pushing on the throttle lever, more fuel is available for the engine to use, and it is able to increase in speed

the upper and lower shift cables on an OMC stern-drive unit. The upper (black) cable runs between the helm and the engine. The lower (red) cable runs between the engine and the stern drive

c) The choke cable – on gasoline engine, the choke cable runs from the helm controls to the carburetor and opens/closes a single flap that cuts off air to the carburetor, ‘choking’ it. With the flap closed, the engine is running on undiluted gas, allowing it to start and warm up easier.

d) The engine stop cable – on diesel engines, the engine stop cable runs from the helm position to the injection pump or governor and cuts of fuel supply to the engine, causing it to stop running

e) The lower shift cable – this is a secondary shift control cable on engines with a stern drive. The main shift cable runs from the helm to a bracket on the engine, where it meets with the lower shift cable, which shifts the gears (from neutral to forward/reverse) on the stern drive unit

In each case, the cable is made of an inner core that slides inside the sheath and allows it to push and pull between the controls and the engine. This inner core can stretch over time, and can bind up within the sheath. If either occurs, the cable should be replaced. Some manufacturers have cable ends that are specifically tailored to their engines or controls – so choosing the right cable type (as well as length) is important.

Throttle Cable the throttle cable on an OMC onboard, connected to the carburetor.

Here are a few symptoms that can be traced back to shift cables that should be replaced:

1) Rough throttle control – when moving the throttle cable, the engine makes ‘leaps’ from idle to very fast, with very little control in between
2) Difficulty in shifting between neutral and forward/reverse – shifting should be smooth – you shouldn’t have to fight to move the lever between gears
3) Having to pull very hard on a choke or engine stop cable to get it to work
4) The engine stalling when shifting gears on a boat with a stern-drive – may indicate that the cable should be adjusted, or replaced.
5) Hearing a grinding noise when the engine is in forward or reverse gear on an outboard or stern drive – this indicates that the engine isn’t fully in gear, and may mean that the cable has stretched and doesn’t have enough tension to fully engage the gear.


Evinrude Outboardshift and throttle cables on an Evinrude outboard.

As you can see – maintaining and updating engine control cables is an important part in ensuring that your engine is running appropriately and safely. Here are a few maintenance tips:

- Lubricate cable ends and connections at least annually. I usually do this during a spring start-up
- Check for tension and ease of shifting regularly. At the earliest sign of struggling to shift gears, check the control cable
- Check the cable ends (at the helm control and at the engine) for any signs of wear or corrosion, and replace as necessary
- Check the pins and locking rings/cotter pins (these hold the cable ends in place) for wear. Replace or install new pins if they appear worn.

 



Ask Andrew Andrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.

Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

 

 

 

 

 

 

Related Articles
Maintenance
  • 07 July 2020
  • By Ethan

Ask Andrew: Tune-ups

Many boats are now on the water after a COVID-imposed hiatus – and with a shortened ‘prep’ period, usually filled with antifouling, polishing, cleaning, engine check-overs and the installation of a new...

Maintenance
  • 10 June 2020
  • By Ethan

Ask Andrew – Pump it up

Boats contain several pumps, each serving a unique purpose and positioned in a way that allows it to do its job effectively. Understanding the why and the how can be important in troubleshooting when an...

Boat Reviews

  • Prev
New at the end of 2019, the 58 Salon Express design features large windows to flood the living ...
No wonder this is one of Regal’s best-selling boats; the Regal 33 Express offers amazing ...
The newest member of Beneteau’s Gran Turismo line is the GT 36 and this yacht brings the style and ...
With a philosophy of quality and 'doing things right Ranger Tugs launches the all new R-25 at the ...
The new Beneteau Swift Trawler 41 renews the spirit of the practical seaworthy cruiser. The ...
The Canadian Yachting test crew last week had the opportunity to run the Bavaria S36 HT at St ...

CY Virtual Video Boat Tours

Virtual Boat ToursWe all love boats and nothing can break us up! So, what better way to spend our time than looking at interesting boats and going aboard in a virtual ride or tour. We have asked our friends at various dealers and manufacturers to help us assemble a one-stop online resource to experience some of the most interesting boats on the market today. Where the CY Team has done a review, we connect you to that expert viewpoint. Our Virtual Show will continue to grow so visit frequently and check it out. If you can’t go boating, you can almost experience the thrill via your screen. Not quite the same, but we hope you enjoy our fine tour collection.

 

Read more about the CY Virtual Boat Tours....................

 

Beneteau Oceanis 30.1As boat builders clamber to create ever-bigger platforms for ever-more generous budgets, the entry-level cruiser has become an elusive animal. Sure, if you want to daysail, there are plenty of small open boats from which to choose, but if you want a freshly built pocket cruiser, you’re in for a long search. Enter French builder Groupe Beneteau, which identified this gap in the market and set about creating the Oceanis 30.1, an adorable little cruiser that resembles her larger siblings in all but length and price. With all she offers, it wouldn’t be a stretch to call her a mini yacht.

Read More about the Beneteau Oceanis 30.1..................

Destinations

  • Prev
On May 19, the New York State Canal Corporation today announced an updated opening schedule for the ...
If you have four hours to enjoy a fine tour of one of Canada’s most interesting waterways (let’s ...
Boom & Batten Restaurant is suspended over the water adjacent to the Songhees Walkway and ...
Provincial Boat Havens are those special places to drop anchor in British Columbia’s West Coast and ...
NW Explorations, a Bellingham, Washington-based yacht charter, brokerage, and marine services ...

DolphinsBy the Canadian Yachting Editors


Canadians are blessed in many ways and especially when it comes to boating. We enjoy some the world’s most beautiful cruising waters and many places are as sheltered as they are scenic.

British Columbia and the Pacific North West plainly have the most breath-taking scenery with the combination of the majestic ocean views and the snow-capped mountains in the distance. It’s like no place on earth when you have a Killer Whale breach beside your little fishing boat.

Read more about Canadian Cruising...........

 

Lifestyle

  • Prev
The Council of British Columbia Yacht Clubs with over 50 yacht club members has become the voice of ...
Classic boat restoration expert and wooden boat builder Stan Hunter recently sent us this great ...
In Mid June, a floatplane plunged into Constance Bay on the Ottawa River after two planes collide ...
Winter is a fun time for sailmakers in Canada. We grind through mountains of repairs and have an ...
The seasoned sailor mapped out an ambitious course around the world — aboard his 28-foot ...
Clean wake: A concept amongst cruising sailors that stresses the impact that individual behaviour ...
This line-up of Beneteaus can to us from our friends at RCR Yachts in NY State where they are ...
As another harsh Victoria winter came to a close, the deck repair and refinishing continued with ...
The Peterborough Canoe Company was formed in 1892 and began production the following year after ...
On one of the sunny days we had recently, Kyle MacTaggart in Honey Harbour ON fired up the Merc to ...

Cobourg Yacht Club - 2015 Sailing instructorsKatherine Stone

Like many other harbours on Lake Ontario, Cobourg has seen its fair share of changes. Screams used to be heard from kids piled into a toboggan on wheels that went hurtling down a wooden slide into the harbour. Above it all was the bustling din from the waterfront of ship’s whistles, train engines, foghorns and thundering coal cars. It is now a rather serene place for the locals and visitors to enjoy various watercraft. Fortunately, the beautiful beach that lines the waterfront is still a star attraction for the town.

Located 95 kilometres east of Toronto and 62 kilometres east of Oshawa on the north edge of Lake Ontario, United Empire Loyalists first starting arriving in the area as early as the 1780s. The first settlement in 1798 was called Buckville, later renamed Amherst, then called Hamilton (after the township) and also nicknamed Hardscrabble. It wasn’t until 1819 that they finally settled on the name of Cobourg, which was incorporated as a town in 1837. In the late 1820s large schooners with passengers and cargo had to anchor well off shore, as there was only a landing wharf. A group of Toronto businessmen formed the Cobourg Harbour Company which built the wooden Eastern Pier from tolls charged for the use of the harbour.

Read more: Cobourg Yacht Club...

Marine Products

  • Prev
Wet decking can compromise passenger safety on boats, particularly when boarding or disembarking. ...
Anyone who has repeatedly used a rag to clean gelcoat, paint and delicate surfaces has seen the ...
The new Mercury Racing 300hp Five‑Blade CNC Cleaver propellers are designed expressly to maximize ...
Beneteau may have outdone itself with introduction of its new Gran Turismo 36, manufactured in ...
Yanmar Power Technology has announced the development of a hydrogen fuel cell system for maritime ...
Kevin Monahan is a retired Canadian Coast Guard officer with more than 20 years of experience ...
The new 2020 PORTS Georgian Bay, North Channel & Lake Huron Guide is available for purchase at ...
Professional boatbuilders don't want to have to redo a job any more than a DIYer. Many choose Life ...
Since its introduction last year, the JBL by Harman Marine BassPro 10" Powered Subwoofer (JBLMBP10) ...
After decades of perusing charts and guidebooks as part of planning a cruise, it was a totally ...