Prop250When was the last time you sent your propeller shaft to the machine shop to be checked? How old are your engine mounts? Have you replaced your cutlass bearing recently? Do I sound like your mother? Well, if she were here, she’d be giving you some important advice! Powerboats and sailboats with inboard engines generally have rubber in the engine mounts, packing material in the stuffing box and a cutlass bearing in the propeller strut.

Of course, there is always a shaft to which the propeller is attached. On recreational boats that get only weekend and occasional vacation trip use, total hours of operation are often low and inboard driveline elements are sufficiently simple and robust that they can last for years without failure…but there is always wear.

You don’t need a broken drive shaft to spoil your day. Constant vibration, heat and noise may be dampening your fun every time the boat is run. It comes down to accurate alignment in the drive train. When things are all on spec, the boat will be at its smoothest and quietest. Plus, it will be a touch more economical and a lot longer lived. You really don’t want to suffer that broken shaft.

So, give them the shaft!

Start the process by having your mechanic send it out and verify that the shaft is straight and has no visible wear spots. A good shaft can be trued up, but one that has been run bent or out of alignment for several seasons, can be ready to snap from fatigue.

Even a very small amount of damage can start a chain reaction of problems. Also, the shaft itself is a large and heavy piece that has to be checked when it is outside the boat. Dropping the shaft requires the coupler between the transmission and the stuffing box to be undone and often the rudder and stock have to be removed to slide the shaft out. It slides out of the stuffing box and through the cutlass bearing in the strut before it’s free.

This is not a simple DYI project because separating the coupler and sliding it out often requires special tools. An amateur with a pry bar can do real damage.

Start the driveline checking process with the shaft because even a minor issue with the shaft can cause noise and vibration problems and if you try to fix those by adjusting engine mounts, you will spend a fair bit of money without fixing your vibration problem.

While you are pulling the shaft, send out your props to be checked for accuracy and balance. You don’t need to hit the shoal to hurt a prop and start noise and vibration there.

How often should you do this? When you notice a problem of course, but the subtle progress of wear means that every few years, it’s worth the modest investment in checking!

Destinations

  • Prev
Located about half way between Shediac and the Miramichi on New Brunswick’s Acadian Coast, the town ...
Suddenly the once forsaken city of Hamilton, Ontario is booming for at least two good reasons.
The Salty Dawg Sailing Association (SDSA) invites all sailors to join a cruising rally from the ...
Long popular with New England and St. John area boaters, Passamaquoddy Bay is too often overlooked ...
We did breakfast yesterday in the Greek port of Piraeus, just outside Athens:strong coffee, crisp ...
After much speculation Prince Harry finally popped the question to American actress and longtime ...
Last January we ran a short piece on the motor boat A Great Story which had been restored by the ...
The Moorings has just announced the launch of its newest Caribbean destination, Antigua. 
Toronto sailor and former RCYC coach/sailing instructor Ryan May is now a US coast guard captain ...
Just before the weekly party at Shirley HeightsSunsail staffer Chris Donahue conducts our chart ...

How to be as Polite as a Canadian at Gulf Island Marine Park Anchorages

Gulf Island Marine ParkStory and photos by Catherine Dook

One summer I sold ice cream and knick-knacks at Montague Harbour Marina. I was standing behind the counter one day, when the phone rang. “There’s a boat at anchor in the middle of the bay that’s been playing loud music for three hours,” complained an irate-sounding male voice. “Can you make them stop?”

“Um, no,” I replied. “The marina has no jurisdiction over the anchorage. Besides, my only weapon is a till.” The man hung up on me.

Now when you think about it, you can understand why the poor fellow was annoyed.

Read more about the Gulf Island Marine Park.....

 

 

Lifestyle

  • Prev
We were all set with this week’s POTW when a real stunner came in as part of a story on the Blind ...
Have your say. Send an email to This email address is being protected from spambots. You need ...
When I was about ten years old I starting racing sailboats on Cape Cod and the sound of the wind ...
I took this photo in July 2017 from our boat Ginger which was anchored and stern tied in Mouat Bay ...
Were we nervous when we returned to Adamant 1 in November? The answer would be a hearty yes. The ...
Just to put it in historical time warp I was a World Sailing Vice President 1976-1994 and President ...
Great icicles! This is not what one expects from the tropical climes of BC. It’s a nice winter ...
Rossiter is a Canadian builder in Markdale, Ontario that builds a nice fleet of rowboats and small ...
Welcome to Photo of the Week 2018. If you are not familiar with this wonderful feature (What???!!!) ...
Living the dream! Longtime CY staffer and now blogger Lynn Lortie with her husband Pat left Midland ...
Canadian Yachting Digital April 2018

Boat Reviews

  • Prev
Commodore’s Boats is a full service shipyard with over 50 years of generational history and ...
Cruisers Yachts debuts the all-new 42 Cantius. The sporty, luxury cruiser will make its first ...
Once again, the designers at Jeanneau have outdone themselves with the innovative new Leader 10.5 ...
The introduction of X-Yachts’Xc range in 2008 has proven itself to be something of a game changer ...
Hull #1 ZINNIA, the all-new, twin outboard MJM 35z left Boston BoatWorks on July 5 for Newport and ...
Following a 10-year hiatus, Richmond, BC-based Crescent Custom Yachts is once again launching ...
According to the folks at Fraser Yacht Sales, you couldn't ask for more - the new Azimut Atlantis ...
During those cold, cold, sunless, dreary months of January and February, I want to remember the fun ...
The Rossiter 23 Classic Day Boatis both a logical extension of the Canadian-built Rossiter line and ...
It's rare for Canadian Yachting magazine to report on the same boat twice, but that is how ...

 

Cruisers Yachts Cantius 42

Cruisers Yachts Cantius 42By John Armstrong and Andy Adams 

The latest new model from Cruisers Yacht sis the Cantius 42 and this yacht made its debut in the fall of 2017, at the Fort Lauderdale International Boat Show. We had the pleasure of going all through this newest Cantius there and clearly, the Cruisers Yachts people continue to refine and expand on all the features that have made the Cantius line such a success.

The new 42 continues the Cantius family resemblance with handsome and distinctive lines including a big section of hull side glazing port and starboard that makes the full-beam mid-ship master stateroom feel very bright and open.

Read more about the Cruisers Yachts Cantius 42...

 

 

Marine Products

  • Prev
We have all had the experience of heading down below on a nice boat only to encounter an unpleasant ...
Last year when this column launched a good deal of time was spent understanding global satellite ...
This article was my first about 10 years ago, and it found it's way to an outdoor editor/writer ...
For a gloomy February we look not only at how an app that works within your phone can be of benefit ...
ZCare Marine, offers effective, eco-safe products to help keep your boat clean. They have products ...
Monaro Marine Ltd. of Richmond, BC, designs and builds its own unique brand of semi-custom 21' to ...
With Garmin it is now possible to use both devices without independently operating two devices with ...
When the Halifax Boat Show opens on February 8th there will be an excellent selection of pontoon ...
The 627 is the largest outboard in world. New cylinder heads and camshaft, an uprated ...
Sirius Signal held a product information session for interested parties prior to demonstrating ...