diy-electrical-propeller-largeDoesn't a propeller look simple? Visually, the size and shape makes it obvious that a propeller kind of "screws" its way through the water and to a casual observer, it looks to be one of the simplest parts on the whole boat.

Well, it's exactly the opposite. Your propeller is the unsung hero of boating. It's probably the single most complex piece of engineering on the boat. The size and shape of the blades and their angle to the hub are just the start of the story. The thickness of the blades, the rake and angle of attack at various points along its length, the finishing of the blade edge, whether or not it has any "cup". These are all factors and there are many more.

Change just one and the performance changes.

Two miles per hour; that's what we lost when we accidentally backed out a little too far and at idle speed in gear; our prop blades just kissed the edge of a rock. After that, the GPS revealed that the boat was running 35.7, not the previous 38 mph. We still got the maximum revs too...just not the speed.

We put the boat on the trailer and looked at the propeller. At first glance, the prop looked to be OK. Expert examination showed that it was out of "index". Index is the space between the blades. Our almost unnoticeable accident could also have put the prop out of "track". Track is the relative height of each point. Sometimes a propeller strike bends all blades equally. The GPS does not lie though. We immediately lost 2 mph off the top speed.

Even minor prop damage can set up a noticeable vibration at various speeds that can cause future damage to gears, seals and drive train parts. Of course, performance and fuel economy can suffer too!

Luckily, there's a great solution to this and it's cheap – sometimes even free and you can do it this winter when your boat is in storage.

This winter is the perfect opportunity for you or your marina to remove your prop and have it checked out. Often, there's only a nominal charge for a prop check that could reveal damage that could be costing you lost speed, wasted fuel, or excess engine vibration.

Many props can be "tuned" or repaired for minor damage, being out of index, or out of track. If a blade is nicked, bent or cracked, it may be possible to repair it and if the prop is badly damaged, you should just replace it anyway.

Props are not inexpensive (although repairs are quite affordable) because they are actually quite tricky to make. They are even harder to design but that's for another article!

We recently traveled to Fond du Lac, Wisconsin where we had the genuine pleasure of touring the Mercury Marine propeller plant to watch their experts cast and machine new stainless steel propellers. The following photographic tour will give you some appreciation of the effort it takes to make a new propeller.

diy-electrical-propeller-large

Incredibly, Mercury has over 500 different wax patterns for propellers. They make a die cast wax pattern in a special wax formulation that later gets recycled. The wax pattern is coated in colloidal silica sand and slurry of binders like a milkshake to build the ceramic up to five layers.

diy-electrical-propeller_2-large

 The ceramic shell is the "investment" in investment casting. The technique goes back to 4000 B.C. While aluminum can be cast in a metal die (making it less expensive), molten stainless steel at 3,000° would simply weld itself to any kind of metal die. Only a ceramic shell can take the heat and later, it has to be smashed off the part.

diy-electrical-propeller_3-large

 The ceramic shells dry in temperature and humidity controlled rooms before going to an autoclave that removes the wax. Next, the now empty ceramic shell goes to a "burn-out" furnace that heats it to 2,000° F to reduce thermal shock in the "pour", burning out any remaining wax and strengthening the shell.

diy-electrical-propeller_4-large

 An induction furnace melts the special Mercury X7 alloy at 3,000°. In a separate oven, the ceramic shells are heated more before being placed on a cart near a special overhead robotic arm. The operator uses that to manipulate with the ladle of molten stainless steel, pouring it carefully and with precision into each ceramic shell.

diy-electrical-propeller_5-large

 Once cooled down, the ceramic shell is broken off leaving a dull gray propeller. It then goes to a highly skilled technician who balances and machines the prop before final polishing. His work is more like art than manufacturing.

diy-electrical-propeller_6-large

 These little Tetrahedron shapes are called "cut media". They are polyester resin with aluminum oxide grit. It's curious that they wear evenly in the huge polishing bin as the propellers slowly rotate. Twenty pounds of cut media is used to polish one propeller at $1.85 a pound!

diy-electrical-propeller_7-large

 The final step is another polishing process using porcelain pellets with aluminum oxide for the final polish. We've skipped over dozens of important details but these are the main steps your new stainless steel prop goes through to be manufactured.

As probably the number one propeller manufacturer on the planet, it still takes Mercury five full days from wax pattern to a boxed product ready to ship!

Boat Reviews

  • Prev
New at the end of 2019, the 58 Salon Express design features large windows to flood the living ...
No wonder this is one of Regal’s best-selling boats; the Regal 33 Express offers amazing ...
The newest member of Beneteau’s Gran Turismo line is the GT 36 and this yacht brings the style and ...
With a philosophy of quality and 'doing things right Ranger Tugs launches the all new R-25 at the ...
The new Beneteau Swift Trawler 41 renews the spirit of the practical seaworthy cruiser. The ...
The Canadian Yachting test crew last week had the opportunity to run the Bavaria S36 HT at St ...

CY Virtual Video Boat Tours

Virtual Boat ToursWe all love boats and nothing can break us up! So, what better way to spend our time than looking at interesting boats and going aboard in a virtual ride or tour. We have asked our friends at various dealers and manufacturers to help us assemble a one-stop online resource to experience some of the most interesting boats on the market today. Where the CY Team has done a review, we connect you to that expert viewpoint. Our Virtual Show will continue to grow so visit frequently and check it out. If you can’t go boating, you can almost experience the thrill via your screen. Not quite the same, but we hope you enjoy our fine tour collection.

 

Read more about the CY Virtual Boat Tours....................

 

Beneteau Oceanis 30.1As boat builders clamber to create ever-bigger platforms for ever-more generous budgets, the entry-level cruiser has become an elusive animal. Sure, if you want to daysail, there are plenty of small open boats from which to choose, but if you want a freshly built pocket cruiser, you’re in for a long search. Enter French builder Groupe Beneteau, which identified this gap in the market and set about creating the Oceanis 30.1, an adorable little cruiser that resembles her larger siblings in all but length and price. With all she offers, it wouldn’t be a stretch to call her a mini yacht.

Read More about the Beneteau Oceanis 30.1..................

Destinations

  • Prev
On May 19, the New York State Canal Corporation today announced an updated opening schedule for the ...
If you have four hours to enjoy a fine tour of one of Canada’s most interesting waterways (let’s ...
Boom & Batten Restaurant is suspended over the water adjacent to the Songhees Walkway and ...
Provincial Boat Havens are those special places to drop anchor in British Columbia’s West Coast and ...
NW Explorations, a Bellingham, Washington-based yacht charter, brokerage, and marine services ...

DolphinsBy the Canadian Yachting Editors


Canadians are blessed in many ways and especially when it comes to boating. We enjoy some the world’s most beautiful cruising waters and many places are as sheltered as they are scenic.

British Columbia and the Pacific North West plainly have the most breath-taking scenery with the combination of the majestic ocean views and the snow-capped mountains in the distance. It’s like no place on earth when you have a Killer Whale breach beside your little fishing boat.

Read more about Canadian Cruising...........

 

Lifestyle

  • Prev
The Council of British Columbia Yacht Clubs with over 50 yacht club members has become the voice of ...
Classic boat restoration expert and wooden boat builder Stan Hunter recently sent us this great ...
In Mid June, a floatplane plunged into Constance Bay on the Ottawa River after two planes collide ...
Winter is a fun time for sailmakers in Canada. We grind through mountains of repairs and have an ...
The seasoned sailor mapped out an ambitious course around the world — aboard his 28-foot ...
Clean wake: A concept amongst cruising sailors that stresses the impact that individual behaviour ...
This line-up of Beneteaus can to us from our friends at RCR Yachts in NY State where they are ...
As another harsh Victoria winter came to a close, the deck repair and refinishing continued with ...
The Peterborough Canoe Company was formed in 1892 and began production the following year after ...
On one of the sunny days we had recently, Kyle MacTaggart in Honey Harbour ON fired up the Merc to ...

Cobourg Yacht Club - 2015 Sailing instructorsKatherine Stone

Like many other harbours on Lake Ontario, Cobourg has seen its fair share of changes. Screams used to be heard from kids piled into a toboggan on wheels that went hurtling down a wooden slide into the harbour. Above it all was the bustling din from the waterfront of ship’s whistles, train engines, foghorns and thundering coal cars. It is now a rather serene place for the locals and visitors to enjoy various watercraft. Fortunately, the beautiful beach that lines the waterfront is still a star attraction for the town.

Located 95 kilometres east of Toronto and 62 kilometres east of Oshawa on the north edge of Lake Ontario, United Empire Loyalists first starting arriving in the area as early as the 1780s. The first settlement in 1798 was called Buckville, later renamed Amherst, then called Hamilton (after the township) and also nicknamed Hardscrabble. It wasn’t until 1819 that they finally settled on the name of Cobourg, which was incorporated as a town in 1837. In the late 1820s large schooners with passengers and cargo had to anchor well off shore, as there was only a landing wharf. A group of Toronto businessmen formed the Cobourg Harbour Company which built the wooden Eastern Pier from tolls charged for the use of the harbour.

Read more: Cobourg Yacht Club...

Marine Products

  • Prev
Wet decking can compromise passenger safety on boats, particularly when boarding or disembarking. ...
Anyone who has repeatedly used a rag to clean gelcoat, paint and delicate surfaces has seen the ...
The new Mercury Racing 300hp Five‑Blade CNC Cleaver propellers are designed expressly to maximize ...
Beneteau may have outdone itself with introduction of its new Gran Turismo 36, manufactured in ...
Yanmar Power Technology has announced the development of a hydrogen fuel cell system for maritime ...
Kevin Monahan is a retired Canadian Coast Guard officer with more than 20 years of experience ...
The new 2020 PORTS Georgian Bay, North Channel & Lake Huron Guide is available for purchase at ...
Professional boatbuilders don't want to have to redo a job any more than a DIYer. Many choose Life ...
Since its introduction last year, the JBL by Harman Marine BassPro 10" Powered Subwoofer (JBLMBP10) ...
After decades of perusing charts and guidebooks as part of planning a cruise, it was a totally ...