diy-electrical-driveline-largejpegWhen was the last time you sent your propeller shaft to the machine shop to be checked?

How old are your engine mounts? Have you replaced your cutlass bearing recently? Do I sound like your mother?

Well, if she were here, she'd be giving you some important advice! Powerboats and sailboats with inboard engines generally have rubber in the engine mounts, packing material in the stuffing box and a cutlass bearing in the propeller strut. Of course, there is always a shaft to which the propeller is attached.

On recreational boats that get only weekend and occasional vacation trip use, total hours of operation are often low and inboard driveline elements are sufficiently simple and robust that they can last for years without failure...but there is always wear.

You don't need a broken drive shaft to spoil your day. Constant vibration, heat and noise may be dampening your fun every time the boat is run. It comes down to accurate alignment in the drive train. When things are all on spec, the boat will be at its smoothest and quietest. Plus, it will be a touch more economical and a lot longer lived. You really don't want to suffer that broken shaft.

So, give them the shaft!

Start the process by having your mechanic send it out and verify that the shaft is straight and has no visible wear spots. A good shaft can be trued up, but one that has been run bent or out of alignment for several seasons, can be ready to snap from fatigue.

Even a very small amount of damage can start a chain reaction of problems. Also, the shaft itself is a large and heavy piece that has to be checked when it is outside the boat. Dropping the shaft requires the coupler between the transmission and the stuffing box to be undone and often the rudder and stock have to be removed to slide the shaft out. It slides out of the stuffing box and through the cutlass bearing in the strut before it's free.

This is not a simple DYI project because separating the coupler and sliding it out often requires special tools. An amateur with a pry bar can do real damage.

Start the driveline checking process with the shaft because even a minor issue with the shaft can cause noise and vibration problems and if you try to fix those by adjusting engine mounts, you will spend a fair bit of money without fixing your vibration problem.

While you are pulling the shaft, send out your props to be checked for accuracy and balance. You don't need to hit the shoal to hurt a prop and start noise and vibration there.

How often should you do this? When you notice a problem of course, but the subtle progress of wear means that every few years, it's worth the modest investment in checking!

Boat Reviews

  • Prev
New at the end of 2019, the 58 Salon Express design features large windows to flood the living ...
No wonder this is one of Regal’s best-selling boats; the Regal 33 Express offers amazing ...
The newest member of Beneteau’s Gran Turismo line is the GT 36 and this yacht brings the style and ...
With a philosophy of quality and 'doing things right Ranger Tugs launches the all new R-25 at the ...
The new Beneteau Swift Trawler 41 renews the spirit of the practical seaworthy cruiser. The ...
The Canadian Yachting test crew last week had the opportunity to run the Bavaria S36 HT at St ...

CY Virtual Video Boat Tours

Virtual Boat ToursWe all love boats and nothing can break us up! So, what better way to spend our time than looking at interesting boats and going aboard in a virtual ride or tour. We have asked our friends at various dealers and manufacturers to help us assemble a one-stop online resource to experience some of the most interesting boats on the market today. Where the CY Team has done a review, we connect you to that expert viewpoint. Our Virtual Show will continue to grow so visit frequently and check it out. If you can’t go boating, you can almost experience the thrill via your screen. Not quite the same, but we hope you enjoy our fine tour collection.

 

Read more about the CY Virtual Boat Tours....................

 

Beneteau Oceanis 30.1As boat builders clamber to create ever-bigger platforms for ever-more generous budgets, the entry-level cruiser has become an elusive animal. Sure, if you want to daysail, there are plenty of small open boats from which to choose, but if you want a freshly built pocket cruiser, you’re in for a long search. Enter French builder Groupe Beneteau, which identified this gap in the market and set about creating the Oceanis 30.1, an adorable little cruiser that resembles her larger siblings in all but length and price. With all she offers, it wouldn’t be a stretch to call her a mini yacht.

Read More about the Beneteau Oceanis 30.1..................

Destinations

  • Prev
On May 19, the New York State Canal Corporation today announced an updated opening schedule for the ...
If you have four hours to enjoy a fine tour of one of Canada’s most interesting waterways (let’s ...
Boom & Batten Restaurant is suspended over the water adjacent to the Songhees Walkway and ...
Provincial Boat Havens are those special places to drop anchor in British Columbia’s West Coast and ...
NW Explorations, a Bellingham, Washington-based yacht charter, brokerage, and marine services ...

DolphinsBy the Canadian Yachting Editors


Canadians are blessed in many ways and especially when it comes to boating. We enjoy some the world’s most beautiful cruising waters and many places are as sheltered as they are scenic.

British Columbia and the Pacific North West plainly have the most breath-taking scenery with the combination of the majestic ocean views and the snow-capped mountains in the distance. It’s like no place on earth when you have a Killer Whale breach beside your little fishing boat.

Read more about Canadian Cruising...........

 

Lifestyle

  • Prev
The Council of British Columbia Yacht Clubs with over 50 yacht club members has become the voice of ...
Classic boat restoration expert and wooden boat builder Stan Hunter recently sent us this great ...
In Mid June, a floatplane plunged into Constance Bay on the Ottawa River after two planes collide ...
Winter is a fun time for sailmakers in Canada. We grind through mountains of repairs and have an ...
The seasoned sailor mapped out an ambitious course around the world — aboard his 28-foot ...
Clean wake: A concept amongst cruising sailors that stresses the impact that individual behaviour ...
This line-up of Beneteaus can to us from our friends at RCR Yachts in NY State where they are ...
As another harsh Victoria winter came to a close, the deck repair and refinishing continued with ...
The Peterborough Canoe Company was formed in 1892 and began production the following year after ...
On one of the sunny days we had recently, Kyle MacTaggart in Honey Harbour ON fired up the Merc to ...

Cobourg Yacht Club - 2015 Sailing instructorsKatherine Stone

Like many other harbours on Lake Ontario, Cobourg has seen its fair share of changes. Screams used to be heard from kids piled into a toboggan on wheels that went hurtling down a wooden slide into the harbour. Above it all was the bustling din from the waterfront of ship’s whistles, train engines, foghorns and thundering coal cars. It is now a rather serene place for the locals and visitors to enjoy various watercraft. Fortunately, the beautiful beach that lines the waterfront is still a star attraction for the town.

Located 95 kilometres east of Toronto and 62 kilometres east of Oshawa on the north edge of Lake Ontario, United Empire Loyalists first starting arriving in the area as early as the 1780s. The first settlement in 1798 was called Buckville, later renamed Amherst, then called Hamilton (after the township) and also nicknamed Hardscrabble. It wasn’t until 1819 that they finally settled on the name of Cobourg, which was incorporated as a town in 1837. In the late 1820s large schooners with passengers and cargo had to anchor well off shore, as there was only a landing wharf. A group of Toronto businessmen formed the Cobourg Harbour Company which built the wooden Eastern Pier from tolls charged for the use of the harbour.

Read more: Cobourg Yacht Club...

Marine Products

  • Prev
Wet decking can compromise passenger safety on boats, particularly when boarding or disembarking. ...
Anyone who has repeatedly used a rag to clean gelcoat, paint and delicate surfaces has seen the ...
The new Mercury Racing 300hp Five‑Blade CNC Cleaver propellers are designed expressly to maximize ...
Beneteau may have outdone itself with introduction of its new Gran Turismo 36, manufactured in ...
Yanmar Power Technology has announced the development of a hydrogen fuel cell system for maritime ...
Kevin Monahan is a retired Canadian Coast Guard officer with more than 20 years of experience ...
The new 2020 PORTS Georgian Bay, North Channel & Lake Huron Guide is available for purchase at ...
Professional boatbuilders don't want to have to redo a job any more than a DIYer. Many choose Life ...
Since its introduction last year, the JBL by Harman Marine BassPro 10" Powered Subwoofer (JBLMBP10) ...
After decades of perusing charts and guidebooks as part of planning a cruise, it was a totally ...