Mar 26, 2020

Rubbing Damage(Left) Damage caused by the vessel rubbing against a dock

Rubbing Damage Repaired(Right) The same area, after repair

 

 

 

 

 

 

Building on our last two editions (Sealants, and Fibreglass, respectively), Gelcoat is the next logical progression – that is, the outer part of the hull and decks. Gelcoat serves two main purposes: To protect the fiberglass beneath it, and to give a cosmetic finish as the outer layer of construction.

In the 1960s, when the mass shift began from wooden to fiberglass boat construction, boats were built almost the same way that wooden boats were, and simply sheathed in fiberglass and paint. There was little understanding of way that fiberglass could provide strength to the wooden components, and where wear would be seen years or decades later. These boats tended to be overbuilt. Modern boats, with decades of strength and destructive testing available, are able to use much lighter materials all around, with just as (or more) strength than their heavier counterparts from days-gone-by.

Because of this shift in boat building technology, Gelcoat application in modern boat production is a bit counterintuitive. Modern boats are made using female moulds: The gelcoat is sprayed 3-5mm thick into a mould in the first step. This layer is then laid up with the fiberglass, resin, and plywood/balsa supporting material on top of it. Once the hull, deck, cockpit, covers and hatch sections have had a chance to dry and harden in their individual moulds, the mould is removed, and the boat components are assembled using sealants and hardware.

Gelcoat CrackingGelcoat cracking at the base of a stanchion.

It should be noted how we define Gelcoat: A gelcoat is a high-quality finish, designed to be applied on a fiberglass surface, using the same technology as polyester resins or epoxies (Ie. They don’t ‘dry’, they ‘cure’ using hardener and chemical reactions). Various colours and thicknesses of base gelcoat are available, with colour pigments available to tint and colour match. Once gelcoat is cured fully, it is a hard shell-like surface

Earlier gelcoats were made of a base white resin, with colour pigments available to match. MEKP hardener is added (as with fiberglass) to allow it to cure. Gelcoat is rolled or brushed on, and can be thinned using acetone to the desired consistency. Gelcoat can be thinned further to allow it to be sprayed on.

Spraying GelcoatSpraying gelcoat on a boot stripe, using Awlgrip and an airbrush tool

A number of advancements have been made in gelcoat technology and there are a number of very high-quality brands available today: Awlgrip, Alexseal and Imron to name a few.

It should be noted that gelcoat differs from marine paint. Marine paint comes in a wide range of colour options, and many are high-quality. Marine paints tend to be slightly less durable than gelcoat, require more maintenance, but are more cost effective than gelcoat finishes (especially when looking at repairs). Interlux and Epifanes are manufacturers of high-quality marine paint.

Awlgrip or Interlux(Left) Awlgrip (gelcoat) or Interlux (marine paint)

Prevail Sprayer(Right) A Prevail sprayer - ideal for small gelcoat applications

 

 

 

 

Gelcoat is glossy and porous and is susceptible to wear and tear from oxidation, dirt and UV exposure. To combat the effects of these, polishing and waxing is recommended annually. Polishing is the process of applying a very fine abrasive (1000-2000grit) to the surface of the gelcoat in order to remove the surface layer, exposing the bright and glossy colour beneath. Professionals do this using a machine polisher and a high-grade applicating pad. This polishing action is followed by a wax application – applying a liquid wax to the surface, rubbing it into the pores of the gelcoat, and then wiping clear. On boats that haven’t been polished in a number of years, sometimes the polishing is preceded by a wet/dry sandpaper application, and a succession of grits of sandpaper and polishing compound.

Repairing gelcoat is a straightforward process on paper, but requires a bit of an artistic flair to finish it well. Gelcoat may be scraped or rubbed down against docks or lines, or may be cracked or crazed on the suface, through impact or due to the flex or tension of the fiberglass below the gelcoat, or the hardware mounted on it.

The repair process is simple enough:

1) Tape off and grind out the repair area – gelocat repairs can get messy, so marking the work area, and protecting the areas adjacent are important. Use a grinder or rotary tool (like a Dremmel tool) to grind out the damaged gelcoat, and through the depths of any cracks to the fiberglass surface.

2) Chamfer the edges of the grinding area – the other edges should be angled so that the new filling compound will adhere well to the surrounding area


3) Apply a fill/fairing compound – using a thickened polyester resin (I like to use microballoons) and I fill the repair area using a putty knife. Polyester resin’s shrink slightly as they cure – so sanding and fairing again are common.

4) Sand fair – sand the area to a fair surface, matching the surrounding area. Sand using progressively higher grit sandpaper to leave a smooth surface

5) Brush, roll or spray gelcoat – gelcoat can be rolled on using a foam or tufted roller, it can be brushed on (watch for brush marks), or it can be sprayed using an automotive-paint-style spray set-up. For smaller jobs, I like using a Preval spray applicator – it includes a small glass jar as a reservoir for thinned gelcoat, along with an aerosol-type sprayer. It can be sprayed much like spray-paint

6) Wet-sand fair – Gelcoat can take 1-2 days to cure if rolled or brushed, but can take up to 7 days when thinned and sprayed. Once cured, the surface should be wet-sanded using a very high-grit (400-2000 grit) to match the surrounding surface

7) Polish to a high gloss. The repair can now be polished and waxed

I would encourage you to attempt small repairs on your own – it’s a great way to learn the art of gelcoat repair and maintenance. If you take this on, protect the work area (spills and mistakes are likely), have acetone nearby to clean up any mistakes, and wear appropriate PPE (Face mask and nitrile gloves). Work in a well-ventilated area, and be conscious of your neighbors.

Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.

Questions or comments for Andrew? Email him directly via: aThis email address is being protected from spambots. You need JavaScript enabled to view it.

Related Articles
Maintenance
  • 07 July 2020
  • By Ethan

Ask Andrew: Tune-ups

Many boats are now on the water after a COVID-imposed hiatus – and with a shortened ‘prep’ period, usually filled with antifouling, polishing, cleaning, engine check-overs and the installation of a new...

Boat Reviews

  • Prev
New at the end of 2019, the 58 Salon Express design features large windows to flood the living ...
No wonder this is one of Regal’s best-selling boats; the Regal 33 Express offers amazing ...
The newest member of Beneteau’s Gran Turismo line is the GT 36 and this yacht brings the style and ...
With a philosophy of quality and 'doing things right Ranger Tugs launches the all new R-25 at the ...
The new Beneteau Swift Trawler 41 renews the spirit of the practical seaworthy cruiser. The ...
The Canadian Yachting test crew last week had the opportunity to run the Bavaria S36 HT at St ...

CY Virtual Video Boat Tours

Virtual Boat ToursWe all love boats and nothing can break us up! So, what better way to spend our time than looking at interesting boats and going aboard in a virtual ride or tour. We have asked our friends at various dealers and manufacturers to help us assemble a one-stop online resource to experience some of the most interesting boats on the market today. Where the CY Team has done a review, we connect you to that expert viewpoint. Our Virtual Show will continue to grow so visit frequently and check it out. If you can’t go boating, you can almost experience the thrill via your screen. Not quite the same, but we hope you enjoy our fine tour collection.

 

Read more about the CY Virtual Boat Tours....................

 

Beneteau Oceanis 30.1As boat builders clamber to create ever-bigger platforms for ever-more generous budgets, the entry-level cruiser has become an elusive animal. Sure, if you want to daysail, there are plenty of small open boats from which to choose, but if you want a freshly built pocket cruiser, you’re in for a long search. Enter French builder Groupe Beneteau, which identified this gap in the market and set about creating the Oceanis 30.1, an adorable little cruiser that resembles her larger siblings in all but length and price. With all she offers, it wouldn’t be a stretch to call her a mini yacht.

Read More about the Beneteau Oceanis 30.1..................

Destinations

  • Prev
On May 19, the New York State Canal Corporation today announced an updated opening schedule for the ...
If you have four hours to enjoy a fine tour of one of Canada’s most interesting waterways (let’s ...
Boom & Batten Restaurant is suspended over the water adjacent to the Songhees Walkway and ...
Provincial Boat Havens are those special places to drop anchor in British Columbia’s West Coast and ...
NW Explorations, a Bellingham, Washington-based yacht charter, brokerage, and marine services ...

DolphinsBy the Canadian Yachting Editors


Canadians are blessed in many ways and especially when it comes to boating. We enjoy some the world’s most beautiful cruising waters and many places are as sheltered as they are scenic.

British Columbia and the Pacific North West plainly have the most breath-taking scenery with the combination of the majestic ocean views and the snow-capped mountains in the distance. It’s like no place on earth when you have a Killer Whale breach beside your little fishing boat.

Read more about Canadian Cruising...........

 

Lifestyle

  • Prev
The Council of British Columbia Yacht Clubs with over 50 yacht club members has become the voice of ...
Classic boat restoration expert and wooden boat builder Stan Hunter recently sent us this great ...
In Mid June, a floatplane plunged into Constance Bay on the Ottawa River after two planes collide ...
Winter is a fun time for sailmakers in Canada. We grind through mountains of repairs and have an ...
The seasoned sailor mapped out an ambitious course around the world — aboard his 28-foot ...
Clean wake: A concept amongst cruising sailors that stresses the impact that individual behaviour ...
This line-up of Beneteaus can to us from our friends at RCR Yachts in NY State where they are ...
As another harsh Victoria winter came to a close, the deck repair and refinishing continued with ...
The Peterborough Canoe Company was formed in 1892 and began production the following year after ...
On one of the sunny days we had recently, Kyle MacTaggart in Honey Harbour ON fired up the Merc to ...

Cobourg Yacht Club - 2015 Sailing instructorsKatherine Stone

Like many other harbours on Lake Ontario, Cobourg has seen its fair share of changes. Screams used to be heard from kids piled into a toboggan on wheels that went hurtling down a wooden slide into the harbour. Above it all was the bustling din from the waterfront of ship’s whistles, train engines, foghorns and thundering coal cars. It is now a rather serene place for the locals and visitors to enjoy various watercraft. Fortunately, the beautiful beach that lines the waterfront is still a star attraction for the town.

Located 95 kilometres east of Toronto and 62 kilometres east of Oshawa on the north edge of Lake Ontario, United Empire Loyalists first starting arriving in the area as early as the 1780s. The first settlement in 1798 was called Buckville, later renamed Amherst, then called Hamilton (after the township) and also nicknamed Hardscrabble. It wasn’t until 1819 that they finally settled on the name of Cobourg, which was incorporated as a town in 1837. In the late 1820s large schooners with passengers and cargo had to anchor well off shore, as there was only a landing wharf. A group of Toronto businessmen formed the Cobourg Harbour Company which built the wooden Eastern Pier from tolls charged for the use of the harbour.

Read more: Cobourg Yacht Club...

Marine Products

  • Prev
Wet decking can compromise passenger safety on boats, particularly when boarding or disembarking. ...
Anyone who has repeatedly used a rag to clean gelcoat, paint and delicate surfaces has seen the ...
The new Mercury Racing 300hp Five‑Blade CNC Cleaver propellers are designed expressly to maximize ...
Beneteau may have outdone itself with introduction of its new Gran Turismo 36, manufactured in ...
Yanmar Power Technology has announced the development of a hydrogen fuel cell system for maritime ...
Kevin Monahan is a retired Canadian Coast Guard officer with more than 20 years of experience ...
The new 2020 PORTS Georgian Bay, North Channel & Lake Huron Guide is available for purchase at ...
Professional boatbuilders don't want to have to redo a job any more than a DIYer. Many choose Life ...
Since its introduction last year, the JBL by Harman Marine BassPro 10" Powered Subwoofer (JBLMBP10) ...
After decades of perusing charts and guidebooks as part of planning a cruise, it was a totally ...