Feb 14, 2019

Ground Bus BarGrounding is always an interesting idea when on a boat. Can a boat be ‘grounded’ when it’s in the water?


Electrical ground is a term used to describe the reference point in an electrical circuit from which voltage is measured, a common return path for electric current, or a direct physical connection to the earth.

Connection to ground is also important in order to trigger protective mechanisms in the event of failure of internal insulation, and also limits the build-up of static electricity.


‘Ground’ is misleading – in that the term in also used in cell phones, cars and boats – none of which are connected to the earth. A different but suitable term is ‘common’. A ‘common’ connection is usually a large conductor (wire) attached to one side of the power supply. The black (negative) conductor running from the boat’s battery to the engine block, could be called ‘common’ rather than ‘ground’.

So why is a ‘ground’ important on a boat?
Wiring Diagram A simple wiring diagram showing the battery, engine block ground, and ground bus-bar


If an electronic device develops a short-circuit from the power supply side to the equipment’s metal case, the case would then be ‘hot’ and would be a potentially dangerous source of electrical shock or ignition. By ‘grounding’ each appliance (whether AC or DC), you are providing an immediate and easy path for the electricity to travel, eliminating the danger of shock and ignition (and reducing the possibility of corrosion). On a boat, this path to ‘ground’ is generally to the engine block. A typical set-up on a boat includes a heavy gauge cable running from each negative battery post to the engine block grounding post. Each electrical appliance is also grounded to a main bus bar, and the bus bar is grounded, using a cable running to the engine block grounding post, as well.

A few important notes about this set-up:

1) Each cable used should be checked against an ampacity chart (discussed in part 1 of this series) to ensure that the cable size is correct, given the amount of current being carried, and the length of cable run

2) Each cable should be secure and torqued to specifications, using appropriate connections (discussed in part 2 of this series)

3) Grounds should be checked periodically, using a multimeter. This will ensure that short circuits, corrosion, and loose connections haven’t crept in, reducing the effectiveness of the grounding efforts.



Bonding WireNote the forward keel boat, with a bonding wire running between it and a common bonding bus bar

‘Bonding’ is a similar but distinct term. Bonding is the practice of electrically tying together all the large metal objects on a boat. This serves multiple purposes: prevents corrosion damage, provides lightening protection, and serves to reduce static electricity build up and provides ignition protection. The items commonly tied together include: fuel tanks, metal casings (water heaters, as an example), keel bolts, propellers/shafts, engine, transmission, stern-drive, and mast steps. The key to a good bonding system is the use of short-runs, with high-conductivity wiring: tinned-copper wiring, of at least #8 AWG (6 AWG if lighting protection is desired) is the rule of thumb suggested. Many bonding systems employ multiple bus bars or a common grounding conductor in order to keep these wire runs as short as possible. The bonding cables used to connect electrical equipment (AC and DC panels, as an example) should be larger than the current-carrying wiring in the circuits (so that if there is a short to the equipment casing, the bonding cable may carry current – and the cabling should be large enough that it wont melt and start a fire).

A typical set-up involves each component to be bonded, bonded separately. This means that components aren’t wired together in series; rather, each component should be bonded individually to a common ground bus, and that ground bus ground to the battery negative post.

Fuel Tank Bonding Wire A fuel tank showing a bonding wire (8AWG) running between the fuel tank and a common bonding bus bar>

A good bonding system will have multiple sized conductors to account for each application. Each component will be bonded individually, and any bonding conductors should be rated to carry current, even though carrying current is not the purpose of bonding.

It’s particularly important to review both grounding and bonding on a boat that has had any equipment changes, electrical upgrades or installations, or significant changes to wiring. Older boats often have incomplete or partial grounding/bonding, and therefore don’t function to protect the boat. Winter layup is a great time to review your systems to make sure that they are installed correctly and are functioning as designed.

 

 


Andrew McDonaldAndrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.


Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Related Articles

Destinations

  • Prev
NW Explorations, a Bellingham, Washington-based yacht charter, brokerage, and marine services ...
If you haven’t cruised the Rideau Canal before, you have missed a special treat and even if you ...
At the 2019 Vancouver International Boat Show I had the pleasure of meeting up with Allyson and ...
Following the harsh impact of Hurricanes Irma and Maria, The British Virgin Islands is making an ...
For the adventurous boater Bunsby Marine Provincial Park is a special place, situated due south of ...
There is good anchoring in Cowichan Bay and nearby, and salt water enough to make any boater happy. ...
We’re gliding through green-blue waters, colours so vivid and bright they hurt your eyes. We’re set ...
The Halifax waterfront has been attracting more and more large yachts in recent years. However, a ...
Ah Canadian simplicity at its finest; small town, big marina. Little Hilton Beach (population ...
Vancouver-based Big Blue Yacht Charters Worldwide owner Emma Murdoch explains that luxury crewed ...


Port of OrilliaTake your boat and a beautiful waterfront setting, pair that with a fantastic musical lineup of over 100 Canadian and international performers, spice it up with an awesome food truck alley, add in an artistically diverse artisan’s marketplace and finish it with a Folkplay area dedicated to children’s fun and you have the successful recipe for the Mariposa Folk Festival.

Each July this longstanding musical tradition kicks off the summer at Tudhope Park in Orillia on the picturesque shores of Lake Couchiching and you can get there by boat. This year’s festival runs July 5-7 and is celebrating 20 years back in the city where it all began 59 years ago.

Read more about the Mariposa.....

 

Lifestyle

  • Prev
John Booth, who passed away just a few weeks ago was one of the most amazingly gifted and ...
We left Vero Beach on Saturday morning with Alicia, a boat from Sweden, following close behind. The ...
At the end of last month, Canadian sailors gathered on the Palma Beach in Palma de Mallorca, Spain ...
In 2019, C-TOW celebrates its 35th anniversary of providing 24/7 “Peace of Mind Boating” for ...
West Vancouver Yacht Club reports that following an independent certification process the Georgia ...
It has been hot in the Abacos this winter. Whoever said this area was cool this time of year must ...
Unfortunately this is not a picture from a boat but was taken on the evening of February 27, 2019 ...
On March 1, Tom Ramshaw of Stoney Lake Yacht Club was honoured with the most prestigious National ...
Vero Beach, aka Velcro Beach, lived up to its reputation again. Our original plan was to be there ...
My husband and I were visiting the Bra d'Or Lake from Newfoundland in our 39 foot Sea Ray ...

Boat Reviews

  • Prev
ILCA is seeking new builders to complement its existing network of manufacturers, the International ...
Nelson Gilbert (1854-1921) began building canoes in Brockville in the 1890s, a time when the sport ...
I have heard a lot of talk lately about trends in yacht clubs where senior membership is getting ...
To get you in the mood for cruising the Boat Show then launching in spring, here’s a boat that ...
Quite simply, the styles of boats have changed. Where in past years a buyer might have been looking ...
At the boat shows, the Ranger Tugs’ classic tugboat lines always grab the crowds, with the wives ...
Sometimes a great idea requires an encore, and French yacht builder Jeanneau got that with the ...
Tactical Custom Boats announces the sale to a North American client of a custom Tactical 77’ – Fast ...
Bruce Elliott is an inventor. And when he sold the technology he developed to build utility poles ...
One often asks of a winning achievement or a fabulous design, could it have possibly been done ...

Grand Banks 60 SkyloungeThe Canadian market has always been a tough nut for yacht designers to figure out. Summer days get really hot; other days are downright cold. There is always the chance things could change in the blink of an eye and let’s be honest, who among us hasn’t stepped off the boat wearing shorts, flip flops and a warm jacket? Canadian yachting has always been a world of contradictions, which is why designing cruising yachts for this market has never been easy. It’s not like Florida or the Med, where weather is dependable throughout the year.

 

 

Read more about the Grand Banks 60 Skylounge............

 

ILCA DinghyAustin, Texas, USA (25 April 2019) – In the wake of last month’s termination of its contract with its European builder, the International Laser Class Association (ILCA) announced today that, from 25 April 2019, all new, class-approved boats will be sold and raced under the “ILCA Dinghy” name. This change will have no impact on existing ILCA-authorized boats and equipment, which will be able to race alongside ILCA Dinghies in all class sanctioned events.


“It’s a big change for a racing class that hasn’t seen anything like this in our almost 50- year history,” said Class President Tracy Usher.

Read More about the ILCA Dinghy............

Marine Products

  • Prev
Finding a car brand that you enjoy while it does what you need can be tough, as they can be ...
Yikes! No boat refrigeration? You’ve Got to be Kidding me!! But then again, true campers don’t use ...
The Walker Bay Venture 14 claims to be the world’s first luxury Explorer Sport Tender. It is ...
Mercury Marine is pleased to announce the launch of the new MerCruiser V8 6.2L 370hp Jet Ready ...
My history with the Cayenne goes back many years, as I was at the launch of the original vehicle ...
Last month, Mercury Marine has announced the launch of the 400hp Verado outboard engine, the ...
Featuring advanced, intuitive 3D controls, Zipwake Dynamic Trim Control Systems deliver a more ...
Gina de Vere approached me at the Canadian Yachting booth at this year’s Vancouver International ...
A revolutionary “assisted docking” system that provides a glimpse into the future of boating ...
After developing the Figaro Beneteau 3, the first production foiling sailing yacht, Groupe Beneteau ...