Mar 8, 2018

Micron CSC HullI once heard an argument at a yacht club. Two old salts, patiently itching to let go lines and raise sail were preparing their boats for launch. The argument went something like this:

Micron CSC applied to the hull and transom, with an inch-gap around the stern-drives

“What kind of antifoul are you using this year?” asked the first.

“It’s AntifoulingPaint”, came the reply.

“Yes, but what kind of antifoul?” pressed the first.

“Paint. For Antifouling”, was the exasperated response.


Fresh VC 17 On Sailboat 320 Fresh VC17 on a sailboat just prior to launch

It was clear to me that the two boat owners were more concerned with semantics than function. I hope that the argument can finally be put to rest, with this article on Antifoul. Antifouling. Paint. Same thing.

Whether you call it antifoul, antifouling, or antifouling paint, it all amounts to the same function: treatment of a boat's hull with a paint or similar substance designed to prevent fouling. Fouling is the accumulation of microorganisms, plants, algae or animals on wetted surfaces. Antifouling paint is applied to prevent this build-up.
This fouling build-up poses problems for watercraft: damage to hull and propulsion systems and efficiency of movement. In extreme cases, accumulation of biofoulers on hulls can increase the vessel’s surface area and friction, leading to increased drag up to 60%. This drag can decrease speed by 10%, and can require up to a 40% increase in fuel consumption to compensate.

micron-csc-on-hull-320.jpg caption: Micron CSC applied to the hull and transom, with an inch-gap around the stern-drives

Racing sailors tremble at the thought of losing 10% hull speed, and power-boaters break out into sweat at the thought of paying 40% more in fuel. Suffice to say: Antifouling is an important process to take, prior to launch.

And we’re not the first to have this conversation. It’s been happening for some 300 years. The first recorded antifouling process was the use of copper plating to sheathe the keel and underwater planking of HMS Alarm in 1761. The copper sheathing was successful in preventing wood-boring worms from damaging the hull, and also prevented the growth of weeds, as the copper produced a oxychloride film when immersed in water. Around 1770, the Royal Navy sheathed the entire fleet! Over time, as more iron was used in ship production, copper sheathing became impracticable, due to galvanic corrosion. Relatively ineffective and expensive paints were developed in the late nineteenth century, but it wasn’t until the 1960’s that the modern version of antifouling was developed: a paint which is self-polishing, and uses seawater’s ability to react with the paint and release antifouling chemicals at a slow and controlled rate. Additionally, the combination of ingredients in modern antifouls prevent any copper present from reacting to other metals present – so galvanic corrosion caused by antifouling is of little concern.

2nd Year Pant 320 Second-year bottom paint - some noticeable wear, but good for another season

Many breakthroughs have taken place in the last 50 years and today we have many brands, types, chemical compositions and colours to suit every type of boat and boater.

Lets break down the types available and their uses:

Two major divisions can be seen: Hard and Soft.

A hard antifoul gives a solid coat that is smooth, thin and hard to the touch – it needs to be scratched, scraped or sanded to remove. Hard antifouls should be applied just before launch, and are rendered ineffective if the boat is removed and relaunched repeatedly. Hard antifouls typically last one season only. Example: VC17

A soft antifoul looks and acts like a layer of paint, it can be removed with a heavy blast of a power washer, and many brands work well on boats that are trailerable and removed from the water and re-launched during the season. Soft antifouls often last multiple seasons. Example: Micron CSC

A decade ago, it was fairly easy to simplify the difference: Hard antifoul for racing sailboats – boats that want as little drag and as smooth a hull surface as possible. Soft antifouls for trailerable boats (sail and power), larger power boats, and sail-boaters who want multi-season protection at the cost of racing speed.

I would suggest this as a place to start – but recent years have added more elements to the mix, including:

- Water based paints – marketed as the most environmentally friendly option

- Copper or non-copper bases (copper being the traditional base to prevent fouling)

- Single vs multi-season protection

- Colour options

- Compatibility with other brands or types of antifoul

- Hull type – wood, fibreglass, steel or aluminum

So – How do you choose which antifoul is right for you?

Start with the type of boat and the way that it’s used: Are you a racer? Cruiser? Does your boat sit at dock more often than not? Freshwater? Salt Water? Is the boat in the water throughout the sailing season or does it come in and out on a trailer or cradle? Is the boat in the water year-round, or is an extended voyage planned?

Next: What type of hull do you have? A bare gelcoat hull will require a layer between the gelcoat and the antifouling (called a ‘barrier coat’, and acts as a primer as provides protection from osmotic blistering). Is there existing antifouling on the hull? If so, some prep work may be in order, or you may choose to apply an antifoul that is designed to go over other types/brands of antifoul. Metal hulls (especially aluminum) typically require an epoxy-type primer prior to applying antifoul

Finally – Coverage, cost and colour. Some antifouls have larger coverage for the same size of paint can (ie it will cover more boat hull than a competitor), but this may not mean a cost savings overall. Run some comparisons if you’re on a strict budget. Blue, green, red and black are quite common amongst competing brands. Pro tip: paint two coats with two different colours. As the top coat wears off over time, the second coat (in a different colour) will be exposed, giving you an easy view of the state of your antifoul when looking at the hull in the off-season.

Antifoul application instructions are dictated by the manufacturer. Each type of antifoul has specific application instructions, including surface preparation, compatibility with other antifouls already on the hull, time of application (sometimes it must be done 12 hours before launch), ambient temperature at the time of application. I encourage you to read and understand the instructions before application – these factors really do matter, and can make the difference between solid protection and a botched job that cracks and peels off the hull.
Job CompleteRemoving tape after completing the work.

If you’re applying antifoul by yourself, be mindful of the safety instructions indicated by the manufacturer. Most of these products are chemical and/or metal based, and exposure can be harmful to humans. Do not breathe fumes or dust, wear a respirator, gloves and eye-protection. Many marinas and yacht clubs will not allow hulls with antifoul to be sanded on the premises (due to the toxic nature of the dust, and the ease with which the dust sticks to and damages any fibreglass that it lands on!). Those marinas and clubs that do allow hull sanding require the area to be properly tarped, shielded and cleaned up thoroughly after work. Check with your yard before beginning work.

Now is a great time to begin your research before the spring rush. You may want to take a good look at your hull to determine what it needs to move forward into 2018, and the type/cost and availability of your preferred antifoul. Look at yard regulations, safety and application instructions. If you’re hoping to hire someone to do the work for you, get in touch soon, as bookings fill up fast as warm weather hits.

 

 



Safe and Happy boating!

Ask Andrew Andrew McDonald is the owner of Lakeside Marine Services – a boat repair/maintenance firm based in Toronto. Andrew has worked in the marine industry for 12 years and is a graduate of the Georgian College ‘Mechanical Techniques - Marine Engine Mechanic’ program.

Questions or comments for Andrew? Email him directly via: This email address is being protected from spambots. You need JavaScript enabled to view it.

Related Articles
Sail
  • 04 April 2018
  • By Ethan

Dufour 412

One often asks of a winning achievement or a fabulous design, could it have possibly been done better? 

Destinations

  • Prev
Located about half way between Shediac and the Miramichi on New Brunswick’s Acadian Coast, the town ...
Suddenly the once forsaken city of Hamilton, Ontario is booming for at least two good reasons.
The Salty Dawg Sailing Association (SDSA) invites all sailors to join a cruising rally from the ...
Long popular with New England and St. John area boaters, Passamaquoddy Bay is too often overlooked ...
We did breakfast yesterday in the Greek port of Piraeus, just outside Athens:strong coffee, crisp ...
After much speculation Prince Harry finally popped the question to American actress and longtime ...
Last January we ran a short piece on the motor boat A Great Story which had been restored by the ...
The Moorings has just announced the launch of its newest Caribbean destination, Antigua. 
Toronto sailor and former RCYC coach/sailing instructor Ryan May is now a US coast guard captain ...
Just before the weekly party at Shirley HeightsSunsail staffer Chris Donahue conducts our chart ...

How to be as Polite as a Canadian at Gulf Island Marine Park Anchorages

Gulf Island Marine ParkStory and photos by Catherine Dook

One summer I sold ice cream and knick-knacks at Montague Harbour Marina. I was standing behind the counter one day, when the phone rang. “There’s a boat at anchor in the middle of the bay that’s been playing loud music for three hours,” complained an irate-sounding male voice. “Can you make them stop?”

“Um, no,” I replied. “The marina has no jurisdiction over the anchorage. Besides, my only weapon is a till.” The man hung up on me.

Now when you think about it, you can understand why the poor fellow was annoyed.

Read more about the Gulf Island Marine Park.....

 

 

Lifestyle

  • Prev
It’s Friday afternoon at the Newport Yacht Club in Stoney Creek, and that can only mean one thing - ...
We were all set with this week’s POTW when a real stunner came in as part of a story on the Blind ...
Have your say. Send an email to This email address is being protected from spambots. You need ...
When I was about ten years old I starting racing sailboats on Cape Cod and the sound of the wind ...
I took this photo in July 2017 from our boat Ginger which was anchored and stern tied in Mouat Bay ...
Were we nervous when we returned to Adamant 1 in November? The answer would be a hearty yes. The ...
Just to put it in historical time warp I was a World Sailing Vice President 1976-1994 and President ...
Great icicles! This is not what one expects from the tropical climes of BC. It’s a nice winter ...
Rossiter is a Canadian builder in Markdale, Ontario that builds a nice fleet of rowboats and small ...
Welcome to Photo of the Week 2018. If you are not familiar with this wonderful feature (What???!!!) ...
Canadian Yachting Digital April 2018

Boat Reviews

  • Prev
Commodore’s Boats is a full service shipyard with over 50 years of generational history and ...
Cruisers Yachts debuts the all-new 42 Cantius. The sporty, luxury cruiser will make its first ...
Once again, the designers at Jeanneau have outdone themselves with the innovative new Leader 10.5 ...
The introduction of X-Yachts’Xc range in 2008 has proven itself to be something of a game changer ...
Hull #1 ZINNIA, the all-new, twin outboard MJM 35z left Boston BoatWorks on July 5 for Newport and ...
Following a 10-year hiatus, Richmond, BC-based Crescent Custom Yachts is once again launching ...
According to the folks at Fraser Yacht Sales, you couldn't ask for more - the new Azimut Atlantis ...
During those cold, cold, sunless, dreary months of January and February, I want to remember the fun ...
The Rossiter 23 Classic Day Boatis both a logical extension of the Canadian-built Rossiter line and ...
It's rare for Canadian Yachting magazine to report on the same boat twice, but that is how ...

 

Dufour 412

Dufour 412By: Katherine Stone

One often asks of a winning achievement or a fabulous design, could it have possibly been done better? The engineers at Dufour Yachts and the Felci Yachts Design group asked that question and listened carefully to suggestions from owners of the earlier, award-winning Dufour 410- one of Dufour’s most successful 12-metre boats. Not only did Dufour make the 412 more attractive and modern, but alsoincorporated amenities that are usually only reserved for larger boats.

We sailed the boat on a gusty, chilly, late autumn day out of Whitby, Ontario, on Lake Ontario, and she handled very well in 20 knotbreezes and three- to four-foot swells.

Read more about the Dufour 412.....

 

 

Marine Products

  • Prev
We have all had the experience of heading down below on a nice boat only to encounter an unpleasant ...
Last year when this column launched a good deal of time was spent understanding global satellite ...
This article was my first about 10 years ago, and it found it's way to an outdoor editor/writer ...
For a gloomy February we look not only at how an app that works within your phone can be of benefit ...
ZCare Marine, offers effective, eco-safe products to help keep your boat clean. They have products ...
Monaro Marine Ltd. of Richmond, BC, designs and builds its own unique brand of semi-custom 21' to ...
With Garmin it is now possible to use both devices without independently operating two devices with ...
When the Halifax Boat Show opens on February 8th there will be an excellent selection of pontoon ...
The 627 is the largest outboard in world. New cylinder heads and camshaft, an uprated ...
Sirius Signal held a product information session for interested parties prior to demonstrating ...